Bedienungsanleitung Croozer Kid Keeke 2019 (Seite 17 von 48) (Englisch)

772388

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

CroozerKid-Kid20-ENG-10-19

Converting the Croozer to a Bicycle Trailer

Installing the axle hitch to the towing bicycle

The hitch assembly is always mounted to the left side of

the bicycle (relative to the direction of travel) and consists

of two parts: a hitch connector (1), which is attached to the

hitch arm, and an axle hitch (2), which must be mounted to

the rear axle of the towing bicycle.

Before installing the axle hitch, you must rst check

whether the bicycle is suitable for towing a trailer. This

information can be obtained from the bicycle manufacturer,

a bicycle shop or the owner’s manual of the bicycle.

It is vitally important to confirm that the towing bicycle is

suitable for pulling trailers. Pulling a trailer with a bicycle

that has not been approved by its manufacturer for use

as a towing bicycle can result in frame breakage or other

material damage. Breakages of this kind could cause ac-

cidents with serious injury or death.

If you are not completely condent about your ability to

install the axle hitch correctly, please consult with, or

have the installation performed by, a professional bicycle

mechanic.

It is vitally important that the axle hitch be properly

installed. An improperly installed axle hitch could come

loose while riding and cause accidents with serious injury

or death.

Installing the axle hitch to a bicycle with a quick-

release axle

Tip: If the bicycle wheel is equipped with a thru axle

(with quick release lever) instead of a conventional

quick-release skewer, the thru axle must be re-

placed with the Croozer Thru Axle available as an

accessory. Other hitch axles are also available as

accessories.

The quick-release lever must be positioned on the right

side of the bicycle (relative to the direction of travel). If the

lever is on the left side, the quick-release skewer must be

removed and reinserted from the right side. Be sure to fol-

low the applicable instructions in the owner’s manual of the

bicycle and/or consult a professional bicycle mechanic.

1. Open the quick-release lever (1) on the rear wheel

of the towing bicycle or loosen the Allen bolt (5 mm),

depending on the type of quick-release skewer. Often,

the open position is indicated on the lever by the word

“OPEN”. In this case, when the word “OPEN” can be

seen, the lever is in the open position.

2. Remove the axle nut (2) of the quick-release skewer

by turning the nut anticlockwise. Use caution: the

spring located just beneath the nut is under tension

and could y off when removing the nut.

3. Fit the axle hitch (3) over the end of the quick-release

skewer without removing the spring.

4. Thread the axle nut (2) back onto the skewer. Tighten

the axle nut at least ve full turns (clockwise).

The axle nut must engage the threads for at least five

full turns in order to ensure adequate clamping force for

holding the rear wheel securely. Failure to tighten the

min. 5 x

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Croozer Kid Keeke 2019 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info