Bedienungsanleitung Croozer Kid Plus 2016 (Seite 22 von 52) (Englisch)

772401

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

20 CroozerKid-KidPlus16-ENG-9-15

Converting the Croozer to a Bicycle Trailer

The tension-adjusting nut must engage the threads for at

least five full turns in order to ensure adequate clamp-

ing force for holding the rear wheel securely. Failure to

tighten the tension-adjusting nut adequately may result

in accidents with serious injury or death. If the quick-

release skewer is too short, it must be replaced. Consult

a professional bicycle mechanic for the appropriate parts

and assistance.

5. Check that the rear wheel of the towing bicycle is

properly aligned, adjusting the position if necessary;

then close the quick-release lever or tighten the Allen

bolt, depending on the type of quick-release axle.

Often, the closed position is indicated on the lever

by the word “CLOSE”. In this case, when the lever

side marked “CLOSE” can be seen, the lever is in the

closed position. If the tension-adjusting nut has been

tightened the proper amount, you will be able to feel

the resistance increase when the lever is about half-

way closed, i.e. parallel to the axle. The adjustment is

correct if you can fully close the lever but with consid-

erable force. In the closed position, the lever should be

parallel to the frame, i.e. it should not stick out to the

side.

6. Check whether the quick-release is securely engaged

by trying to rotate the endcap of the mechanism

(where the lever is attached) without opening the lever.

If the endcap is loose enough to rotate, then the

clamping force is inadequate. In this case, open the

lever, and tighten the tension-adjusting nut half a turn

clockwise. Repeat steps 5 and 6.

If it is impossible to push the quick-release lever into

the closed position, then open the lever, and unscrew

the tension-adjusting nut half a turn anticlockwise.

Repeat steps 5 and 6. Keep in mind that the tension-

adjusting nut must engage the threads of the quick-

release skewer for at least ve full turns.

The tension-adjusting nut must engage the threads for at

least five full turns in order to ensure adequate clamp-

ing force for holding the rear wheel securely. Failure to

tighten the tension-adjusting nut adequately may result in

accidents with serious injury or death. If it is not possible

to tighten the tension-adjusting nut five full turns, then the

quick-release skewer is too short and must be replaced.

An extra-long quick-release axle is available as an ac-

cessory. Consult a professional bicycle mechanic for the

appropriate parts and assistance.

7. Finally, hold the rear wheel with both hands and try to

rock it back and forth to check that the wheel is held

securely in the dropouts.

The rear wheel of the towing bicycle must be properly

attached after the axle hitch has been installed. Riding

with an improperly installed rear wheel can result in acci-

dents with serious injury or death. Follow the instructions

and warnings given in the owner’s manual of the towing

bicycle. There are many different types of axles. When in

doubt, consult a professional bicycle mechanic.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Croozer Kid Plus 2016 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Croozer Kid Plus 2016

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info