Bedienungsanleitung Cupra Ateca 2023 (Seite 270 von 355) (Englisch)

817294

270

Zoom out

Zoom in

Vorherige Seite

1/355

Nächste Seite

270

Fuel and exhaust gas cleaning

●Consider the legal speed limits as well as the

recommended gears.

●End the regeneration journey once the con-

trol warning lamp has gone out.

If the warning lamp stays on after 30 minutes

of running in regeneration mode, have a speci-

alised workshop repair the fault.

Regeneration of the particulate lter (only

for 2.0l and 2.5l TSI engines)

Requirements for the regeneration journey:

the engine is at operating temperature.

● Drive at a speed of at least 80 km/h

›››page270.

●Completely remove your foot from the ac-

celerator pedal for a few seconds to let the

vehicle roll with the gear engaged.

●Consider the legal speed limits as well as the

recommended gears.

●Repeat this procedure (accelerate and let

roll) until the control lamp turns o.

This procedure involves an autonomous par-

ticulate lter cleaning process and may take

some time.

If the warning lamp does not turn o, go im-

mediately to a specialised workshop to repair

the fault.

WARNING

Always adjust your speed to suit the weather

conditions, roads, braking distance and traf-

c if the particulate lter is in its regenera-

tion phase. Route recommendations should

never make you disregard each country's

specic traic regulations.

Note

If during the particulate lter regeneration

process you also get a fuel reserve warning ,

the process may be interrupted. Refuel and

continue with the particulate lter regenera-

tion process.

NOTICE

● When the exhaust system detects that the

particulate lter is close to saturation, the

self-cleaning function of this system recom-

mends optimal driving for this function.

●Due to the high temperatures caused by

the regeneration of the particulate lter, it is

possible that the radiator fan will activate af-

ter stopping the engine, even it its operating

temperature has not been reached.

●Noise, smells and high idle speeds can oc-

cur during regeneration.

●Always use the correct engine oil and the

correct fuel to make sure the useful life of

the particulate lter is not aected. Also

avoid making short trips all the time.

Troubleshooting

Fault in the emission control system.

The indicator lamp lights up yellow.

Reduce speed and drive carefully to the near-

est specialised workshop to have the engine

checked.

Combustion failures that can damage

the catalytic converter.

The control lamp ashes yellow.

Reduce speed and drive carefully to the near-

est specialised workshop to have the engine

checked.

Particulate lter blocked

The indicator lamp lights up yellow

›››page269..

Fault in the petrol engine manage-

ment.

The indicator lamp lights up yellow.

Have the engine checked as soon as possible

by a specialised workshop.

When the ignition is switched on, the

(Electronic Power Control) lamp lights up and

should go o once the engine has started.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2023 Seite 270

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info