Bedienungsanleitung Cupra Ateca 2023 (Seite 290 von 355) (Englisch)

817294

290

Zoom out

Zoom in

Vorherige Seite

1/355

Nächste Seite

290

Checking and relling levels

Fig.195 Front compartment: coolant

expansion tank cap.

Previous steps

●Park the vehicle on a rm, at surface.

●Wait until the engine has fully cooled ››› .

●Open the front bonnet.

●The motor coolant expansion tank can be

recognised by the symbol on the cap

›››Fig.195

Check the level

When the vehicle is delivered (new vehicles),

the coolant may be above the marked area.

This is normal. It is not necessary to suck the

coolant out.

●When the engine is cold, check the coolant

level using the side marking on the expansion

tank ›››Fig.194. The coolant level should be

between the marks.

● If the level is below the minimum level mark

( ) on the tank, top up with coolant. When

the motor is warm, the coolant level may be

slightly above the upper mark.

Topping up the uid

When the motor coolant level is too low, the

coolant warning light comes on. In this case,

immediately seek assistance from specialist

personnel.

If the coolant level is too low and there is no

workshop nearby, note the following:

●Always protect your face, hands and arms

from hot coolant or steam by placing a suita-

ble cloth over the cap of the motor coolant

expansion tank.

●Carefully unscrew the cap ››› .

●Only top up with fresh coolant according to

CUPRA specications ›››page289.

●Only top up with coolant if there is still some

coolant left in the expansion tank; otherwise

the motor could be damaged! If you do not see

any coolant in the expansion tank, do not con-

tinue driving and seek specialist assistance.

● If there is still some coolant left in the ex-

pansion tank, top up with coolant up to the

tank’s upper mark and check the level the next

day. If the level drops again, go to a workshop

and request a check of the cooling system.

●The coolant level must be between the

marks on the expansion tank ›››Fig.194.

Never exceed the top edge of the marked

area ››› .

●Screw the cap on tightly.

● If engine coolant with the recommended

specications is not available in an emergency,

do not use any other coolant additive! In this

case, top up with distilled water ››› only.

Next, ensure that the recommended additive

is topped up as soon as possible in the correct

proportion ›››page289.

WARNING

Steam and hot motor coolant can cause se-

vere burns.

●Never open the front bonnet if you see

or hear steam or coolant escaping from the

front compartment. Always wait until you can

no longer see or hear steam or coolant es-

caping. Touching hot parts can result in skin

burns.

●Before opening the front bonnet, please

note the following:

–Apply the electronic parking brake.

–Always keep children away from the front

compartment and never leave them unat-

tended.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Ateca 2023 Seite 290

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Ateca 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info