Bedienungsanleitung Cupra Formentor 2024 (Seite 359 von 404) (Englisch)

817300

359

Zoom out

Zoom in

Vorherige Seite

1/404

Nächste Seite

Wheels and tyres

357

Tyre pressure monitor system

ment panel through a warning lamp and a

warning to the driver ›››Fig.239. If only one

tyre is aected, its position on the vehicle will

be indicated.

Loss of pressure: Check left tyre

pressure!

Change in wheel diameter

The wheel diameter changes when:

●Tyre pressure is changed manually.

●The tyre pressure is insuicient.

●The tyre's structure is damaged.

●The vehicle is not level due to a load.

● The wheels on an axle are subject to a heav-

ier load (e.g. with a heavy load).

●The vehicle is tted with snow chains.

●The temporary spare wheel is tted.

●One wheel has been changed on an axle.

There may be a delay in the reaction of the tyre

pressure monitoring indicator or it may not

indicate anything under certain circumstances

(e.g. sporty driving, snow-covered or unpaved

roads, or when driving with snow chains).

Calibrate the tyre pressure monitoring indi-

cator

After changing the tyre pressure or replac-

ing one or more wheels, the tyre pressure

monitoring indicator must be recalibrated.

This should also be done, for example, when

switching the front and rear tyres.

It should be calibrated with the vehicle stop-

ped and its tyres cold. If calibrated while the

tyres are hot, the pressure check and calibra-

tion procedure should be repeated when cold

before the next trip.

●Switch the ignition on.

●Save the new ination pressure in the Info-

tainment system: function button > Ve-

hicle info > Vehicle status ›››page33.

●OR: through the Service menu on the in-

strument cluster ›››page27.

The tyre pressure loss indicator uses the ABS

sensors to compare the turns of each wheel

and, therefore, their tread circumferences,

among other aspects. The set values are col-

lected and monitored after a long journey at

dierent speeds.

For example, if the wheels are under very

heavy loads, the tyre pressure must be in-

creased to the total recommended tyre pres-

sure before calibration ›››Fig.239.

WARNING

If the tyres are inated to dierent pressures,

or to a pressure that is too low, a tyre may be

damaged and control of the vehicle may be

lost. This could lead to a serious or even fatal

accident.

●If the lamp lights up, reduce speed im-

mediately and avoid any sudden turning or

braking manoeuvres. Stop as soon as possi-

ble, and check the pressure and status of all

tyres.

●The tyre pressure loss indicator only works

correctly if all the tyres are at the correct

pressure when cold, and it is subsequently

calibrated according to the described proce-

dure.

●If the tyres have no punctures and do not

need to be replaced immediately, drive to the

nearest specialist workshop at low speed and

have the tyre pressure checked and correc-

ted.

Note

●When driving for the rst time with new

tyres at high speeds, the tyres may expand

slightly, which may result in an air pressure

warning.

●If a low tyre pressure is detected when the

ignition is switched on, an audible warning

will sound. If the system fails, an audible sig-

nal sounds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor 2024 Seite 359

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor 2024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info