Bedienungsanleitung Cupra Formentor 2024 (Seite 362 von 404) (Englisch)

817300

362

Zoom out

Zoom in

Vorherige Seite

1/404

Nächste Seite

360

Wheels and tyres

●Shake the tyre sealant bottle vigorously

›››Fig.240 10 .

●Screw the tyre ination hose ›››Fig.240 3

into the tyre sealant bottle. The bottle's seal

will break automatically.

●Remove the ller cap ›››Fig.240 3 and

screw the open end of the tube into the tyre

valve.

●With the bottle upside down, empty all of

the contents into the tyre.

●Remove the bottle from the valve.

●Replace the howitzer with the device

›››Fig.240 1 onto the tyre valve.

Inating the tyre

●Screw the tyre ination tube of the compres-

sor ›››Fig.240 8 on the tyre valve.

● Check that the air evacuation screw is

closed ›››Fig.240 6 .

●Start the engine and leave it running.

●Attach the connector ›››Fig.240 9 to the

vehicle’s 12 volt power outlet ›››page238.

●Switch on the air compressor with ON/OFF

switch ›››Fig.240 5 .

●Keep the air compressor running until it

reaches a pressure of 2.0-2.5 bar (29-36psi/

200-250kPa). A maximum of 8 minutes.

●Disconnect the air compressor.

●If it does not reach the pressure indicated,

unscrew the tyre inator tube from the valve.

● Move the vehicle 10m so that the sealant is

distributed throughout the tyre.

●Screw the compressor tyre inator into the

valve.

●Repeat the ination process.

●If it still does not come up to pressure, the

tyre is too badly damaged. Stop and seek assis-

tance from authorised personnel.

●Disconnect the air compressor. Unscrew the

tyre ination tube from the tyre valve.

●When the tyre pressure is between 2.5 and

2.0 bars, continue driving without exceeding

80km/h (50 mph).

●Attach the sticker ›››Fig.240 2 to the in-

strument panel display, within the driver's eld

of vision.

●Check the pressure again after 10minutes

›››page360.

WARNING

When inating the wheel, the air compressor

and the inator tube may become hot.

●Protect hands and skin from hot parts.

●Do not place the hot exible inator tube

or hot air compressor on ammable material.

●Allow them to cool before storing the de-

vice.

● If it is not possible to inate the tyre to at

least 2.0bars (29psi / 200kPa), the tyre is

too badly damaged. The sealant is not in a

good condition to seal the tyre. Do not con-

tinue driving. Seek specialist assistance.

NOTICE

Switch o the air compressor after a maxi-

mum of 8 operational minutes to avoid over-

heating! Before switching on the air com-

pressor again, let it cool for several minutes.

Check after 10 minutes of driving

Screw in the inator tube ›››Fig.240 8 again

and check the pressure on the gauge 7.

1.3bar (19psi / 130kPa) and lower:

●Stop the vehicle! The tyre cannot be sealed

suiciently with the tyre mobility set.

●You should obtain professional assistance

››› .

1.4 bar (20 psi/140 kPa) and higher:

●Set the tyre pressure to the correct value

again.

●Carefully resume your journey until you

reach the nearest specialised workshop with-

out exceeding 80km/h (50mph).

●Have the damaged tyre replaced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cupra Formentor 2024 Seite 362

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cupra Formentor 2024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info