Bedienungsanleitung D-Link DWL-8710AP (Seite 96 von 136) (Englisch)

728146

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Unied Access Point Administrator’s Guide

Page 96

October 2017

Section 8 - Conguring Client Quality of Service (QoS)

Field Description

ACL Type Select the type of ACL to congure:

•) IPv4

•) IPv6

•) MAC

IPv4 and IPv6 ACLs control access to network resources based on Layer 3 and Layer 4

criteria. MAC ACLs control access based on Layer 2 criteria.

ACL Rule Conguration

ACL Name - ACL

Type

Select the ACL to congure with the new rule. The list contains all ACLs added in the ACL

Conguration section.

Rule To congure a new rule to add to the selected ACL, select New Rule. To add an existing rule

to an ACL or to modify a rule, select the rule number.

When an ACL has multiple rules, the rules are applied to the packet or frame in the order in

which you add them to the ACL. There is an implicit deny all rule as the nal rule.

Action Species whether the ACL rule permits or denies an action.

•) When you select Permit, the rule allows all trafc that meets the rule criteria to enter or

exit the AP (depending on the ACL direction you select). Trafc that does not meet the

criteria is dropped.

•) When you select Deny, the rule blocks all trafc that meets the rule criteria from

entering or exiting the AP (depending on the ACL direction you select). Trafc that

does not meet the criteria is forwarded unless this rule is the nal rule. Because there

is an implicit deny all rule at the end of every ACL, trafc that is not explicitly permitted

is dropped.

Match Every Indicates that the rule, which either has a permit or deny action, will match the frame or

packet regardless of its contents.

If you select this eld, you cannot congure any additional match criteria. The Match Every

option is selected by default for a new rule. You must clear the option to congure other

match elds.

IPv4 ACL

Protocol Select the Protocol eld to use an L3 or L4 protocol match condition based on the value of

the IP Protocol eld in IPv4 packets or the Next Header eld of IPv6 packets.

Once you select the eld, choose the protocol to match by keyword or enter a protocol ID.

Select From List

Select one of the following protocols from the list:

•) IP

•) ICMP

•) IGMP

•) TCP

•) UDP

Match to Value

To match a protocol that is not listed by name, enter the protocol ID.

The protocol ID is a standard value assigned by the IANA. The range is a number from

0–255.

Source IP Address Select this eld to require a packet’s source IP address to match the address listed here.

Enter an IP address in the appropriate eld to apply this criteria.

Wild Card Mask Species the source IP address wildcard mask.

The wild card masks determines which bits are used and which bits are ignored. A wild card

mask of 255.255.255.255 indicates that no bit is important. A wildcard of 0.0.0.0 indicates

that all of the bits are important. This eld is required when Source IP Address is checked.

A wild card mask is, in essence, the inverse of a subnet mask. For example, to match the

criteria to a single host address, use a wildcard mask of 0.0.0.0. To match the criteria to a

24-bit subnet (for example 192.168.10.0/24), use a wild card mask of 0.0.0.255.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

D-Link DWL-8710AP Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info