Bedienungsanleitung Dali SUB K-14F (Seite 10 von 91) (Deutsch, Englisch, Dänisch, Französisch)

745214

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

3) In your listening position, play music of the type previously described.

4) Toggle between 0° and 180° while focusing on the bass output.

The optimal setting of the PHASE switch is where you experience maximum bass output.

5.2 VOLUME ADJUSTMENT

On the rear of the subwoofer you can increase or reduce the volume by turning the VOLUME

control clockwise or counter clockwise.

The volume should be adjusted so that the bass matches the level of your main speakers. You

should be able to appreciate your subwoofer’s contribution to the overall sound, without it ever

being overpowering. Bass must be tight and accurate so that the subwoofer reproduces the

exact amount of bass present in the music/soundtrack; no more, no less. When installing the

DALI SUB K-14 F in a surround sound system, we recommend selecting a xed level on the

subwoofer and adjusting the subwoofer output using the surround (pre-) amplier’s/receiver’s

setup function.

If bass levels are set too high, distortion will reduce the quality of your listening experience.

Remember that you can boost the bass level by selecting a physical position close to the wall

or even better – in a corner (see chapter “3.0 Positioning”).

5.3 CROSSOVER FREQUENCY ADJUSTMENT

Once you have set the phase and the volume level, you need to adjust the frequency overlap

between the main speakers and the DALI SUB K-14 F.

5.3.1 USING LINE INPUT

The crossover frequency adjustment on the subwoofer is only possible when using the LINE INPUT(S).

On the rear of the subwoofer, adjust the CROSSOVER control upwards until you can hear the

bass is even with no drop-outs (Frequency range 40-120 Hz). Smaller speakers typically require

a higher crossover point, whereas larger speakers will accept a lower crossover point. For

example when using your DALI SUB K-14 F together with DALI ZENSOR 1, we recommend a

crossover point of approximately 90 Hz.

After having adjusted the crossover frequency you may have to re-adjust the volume to

optimise performance.

5.3.2 USING LFE INPUT

When connecting your DALI SUB K-14 F to smaller speakers, e.g. the DALI ZENSOR 1, we

recommend a crossover point of approximately 90 Hz. This must be entered in the menu system

of your (pre-) amplier. You might need to enter the ‘small’ setting when selecting type of front

speakers in the AV receiver menu.

Connecting larger speakers (typically oor-standing front speakers) will allow you to choose a

lower crossover point, and to dene your speakers as ‘large’ in the menu system.

If in doubt about the capacity of your speakers, we recommend setting the crossover point quite

high, dening your speakers as small, and nally reducing the crossover point to the lowest

possible position while maintaining an even bass with no drop-outs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dali SUB K-14F Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info