Bedienungsanleitung Defort DEC-2046N (Seite 11 von 100) (Alle Sprachen)

555841

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Never operate the chain saw with arms fully extended. Do not

attempt to saw areas which are difﬁ cult to reach, or on a ladder.

Never saw above shoulder height.

Sawing is optimized when the chain speed remains steady

during cutting. Beware when reaching the end of the cut. The

weight of the chain saw changes unexpectedly as it cuts free

from the wood. Danger of injury to the legs and feet.

Always remove the chain saw from a wood cut while the saw

chain is running.

MAINTENANCE AND SERVICE

Maintenance and Cleaning

● Warning! Switch off, remove plug from mains before adjust-

ing cleaning or if the cable is cut, damaged or entangled.

● For safe and proper working, always keep the machine and

ventilation slots clean.

Note: To ensure long and reliable service, carry out the fol-

lowing maintenance regularly. Regulary check the chain saw

for obvious defects such as loose, dislodged or damaged saw

chain and chain bar, loose ﬁ xings and worn or damaged com-

ponents.

RUN-DOWN BRAKE/KICKBACK BRAKE

The chain saw is equipped with two safety features:

The run-down brake stops the saw chain after releasing the

On/Off switch 3.

The kickback brake is a safety mechanism activated through

the front hand guard 5 when kickback occurs. Chain stop re-

sponse time is 0.1 seconds.

WORKING WITH THE CHAIN SAW

Before Cutting

Before starting operation and periodically during cutting, carry

out the following checks:

– Is the chain saw in a fail-safe condition?

– Is the oil reservoir ﬁ lled? Check oil level gauge prior to start-

ing and regularly during operation. Reﬁ ll oil when oil level has

reached the bottom edge of the viewing glass.

The oil tank ﬁ lling will last approx. 15 minutes, depending on

sawing intensity and stops.

– Is the saw chain properly tensioned and sharp? Check chain

tension every 10 minutes during operation. Upon initial opera-

tion, new chains can lengthen considerably. The condition of

the chain inﬂ uences the cutting performance.

Only a sharp chain protects from overload.

– Is the kickback brake deactivated and its function ensured?

– Are you wearing the required protective equipment? Wear

safety glasses and hearing protection. Further protective equip-

ment for head, hands, legs and feet is recommended.

Suitable protective clothing reduces the danger of injury from

thrown about cutting material and accidental touching of the

saw chain.

KICKBACK

Kickback is the sudden backward/upward motion of the chain

saw, occuring when the chain (at the tip of the chain bar) comes

in contact with a log or wood, or when the chain becomes

jammed.

When kickback occurs, the chainsaw reacts unpredictable and

can cause heavy injuries to the operator or bystanders. Par-

ticular attention must be given when sawing sidewards, slanted

or during length cuts, as the gripping teeth 12 usually can not

be applied.

To avoid kickback:

– Saw with the chain bar at a ﬂ at angle.

– Never work with a loose, widely stretched or heavily worn

out saw chain.

– Sharpen the saw chain as speciﬁ ed.

– Never saw above shoulder height.

– Never work with the tip of the chain.

– Always hold a chain saw ﬁ rmly with both hands.

– Apply the metal gripping teeth 12 for leverage.

– Ensure correct chain tension.

GENERAL BEHAVIOUR

Always hold the chain saw ﬁ rmly with both hands. Front handle

with the left hand and rear handle with the right hand. Fully

grip both handles with thumb and ﬁ ngers at all times during op-

eration. Never operate chain saw using only one hand. Ensure

power cord is located to the rear, and keep it out of the range

of the saw chain and cutting material; position yourself in such

a manner that the mains cable can not get caught in branches

and twigs. Use the chain saw only with secure footing. Hold the

chain saw at the right-hand side of your body.

The chain must be running at full speed before it makes contact

with the wood. Use the gripping teeth 12 to support the chain

saw on the wood. Use the gripping teeth as a leverage point

while cutting.

Reset the gripping teeth at a lower point when sawing thicker

logs or tree trunks. For this, pull the chain saw slightly back-

wards until the gripping teeth release, and reposition at lower

level to continue sawing. Do not remove the chain saw com-

pletely out of the cut.

Do not force the saw chain while cutting, let the chain do the

work, using the gripping teeth 12 to apply minimal leverage

pressure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DEC-2046N Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info