Bedienungsanleitung Defort DLM-1010N (Seite 9 von 96) (Alle Sprachen)

555836

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

3. ASSEMBLY

We recommend assembling the lawnmower in the en-

closed space on an even surface or on a special work-

ing table. You will need a cross-tip screwdriver during

the assembly. Start the assembly after the identiﬁ cation

of all parts (ﬁ g. 1)

• Upon removal of the lawnmower from the box, put

the lower part of the handle (5) in the apertures of

the body. Afterwards, lift the cover and fasten the

ends of the handle in the body with selftapping

screws from the back side.

• Fasten the cable hanger (10) to the upper part of the

handle (6).

• Connect the cable to the lawnmower’s handle with

two clamps.

• Join the upper part of the handle (6) with lower parts

(5) and fasten thereof with a screw (7) and a nut (8),

placed into a plastic assembly wrench.

• Screw the wheels (11 and 12) on. All wheels should

be fastened on the same height.

• The both parts of the grass reservoir (4) shall be

pushed into the apertures until hearing a click.

REPLACING THE CUTTING BLADE

• Switch off and remove the plug from mains before

replacing the blade.

• Note that the wings of the knife shall be directed up-

wards for fastening.

• A ﬂ at or other hexagon spanner of 24 size is used for

unscrewing and screwing of the blade.

• Please note that the head of the screw fastening the

blade is made from plastic material; accordingly, the

force applied onto the screw during the ﬁ xing of the

blade shall be 10-16 Nm.

• Replace the cutting knife with the knife of the type

speciﬁ ed only.

4. USE

Operation

The essence of operation of the lawnmower is a hori-

zontally cutting knife fastened to the vertical shaft of the

motor; the knife, which rotates with a speed of approxi-

mately 3000 r/min. cuts the grass at the preselected

height. Cut grass is thrown into the bag via an aperture

in the rear side of the lawnmower under the impact of

centrifugal force and the pressure resulting from the ro-

tation of the knife. Proper positioning of the knife is of

great signiﬁ cance for this process.

Switching ON and OFF (ﬁ g.2)

1. push the round button with one hand

2. draw and hold the switch handle with another hand

3. release the round button

4. hold the switch handle during the entire period of

lawnmower operation

5. releasing the switch handle will switch off the lawn-

mower

User tips

Please remember the most important rule for lawn care

- mow grass instead of plants growing therein. The

mowing procedure shall be repeated once in two-to-

three days with grass growing again fast. Lawnmower

• Before using, always check if the blades, blade bolts

and cutter assembly are not worn or damaged. Re-

place worn or damaged blades and bolts in sets to

preserve balance.

• On multi-bladed appliances, take care as rotating

one blade can cause other blades to rotate.

Operation

• Mow only in daylight or in good artiﬁ cial light.

• Avoid operating the appliance in wet grass, where

feasible.

• Always be sure of your footing on slopes.

• Walk, never run.

• For wheeled rotary mowers, mow across the face of

slopes, never up and down.

• Exercise extreme caution when changing direction

on slopes.

• Do not mow excessively steep slopes.

• Use extreme caution when reversing or pulling the

appliance towards you.

• Stop the blade(s) if the appliance has to be tilted

for transportation when crossing surfaces other than

grass, and when transporting the appliance to and

form the area to be mowed.

• Never operate the appliance with defective guards

or shields, or without safety devices, for example

deﬂ ectors and/or grass catchers, in place.

• Switch on the motor according to instructions and

with feet well away from the blade(s).

• Do not tilt the appliance when switching on the mo-

tor, except if the appliance has to be tilted for start-

ing. In this case, do not tilt it more than absolutely

necessary and lift only the part which is away from

the operator. Always ensure that both hands are in

the operating position before returning the appliance

to the ground.

• Do not put hands or feet near or under rotating parts.

For rotary mowers, keep clear of the discharge

opening at all times.

• Never pick up or carry an appliance while the motor

is running.

• Pull the plug from the socket:

• whenever you leave the machine;

• before clearing a blockage;

• before checking, cleaning or working on the appli-

ance;

• after striking a foreign object. Inspect the appliance

for damage and make repairs as necessary;

• if the appliance starts to vibrate abnormally (check

immediately).

MAINTENANCE AND STORAGE

• Keep all nuts, bolts, and screws tight to be sure the

appliance is in safe working condition.

• Check the grass catcher frequently for wear of dete-

rioration.

• Replace worn of damaged parts for safety.

• For cylinder mowers, be careful during adjustment

of the appliance to prevent entrapment of the ﬁ ngers

between moving blades and ﬁ xed parts of the appli-

ance.

• For rotary mowers, ensure that only replacement

cutting means of the right type are used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DLM-1010N Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info