Bedienungsanleitung Defort DPC-1316 (Seite 14 von 72) (Deutsch, Englisch, Französisch)

555842

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Checking chain lubrication

• Check the chain lubrication each time you refuel.

See instructions under the heading Lubricating the

bar tip sprocket.

Aim the tip of the bar at a light coloured surface about

20 cm (8 inches) away. After 1 minute running at 3/4

throttle you should see a distinct line of oil on the light

surface.

If the chain lubrication is not working:

• Check that the oil channel in the bar is not obstruct-

ed.

Clean if necessary.

• Check that the groove in the edge of the bar is

clean.

Clean if necessary.

• Check that the bar tip sprocket turns freely and that

the lubricating hole in the tip sprocket is not blocked.

Clean and lubricate if necessary.

If the chain lubrication system is still not working after

carrying out the above checks and associated meas-

ures you should contact your service agent.

Chain drive sprocket

The clutch drum is ﬁ tted with a Spur sprocket (the chain

sprocket is welded on the drum).

Regularly check the degree of wear on the drive

sprocket.

Replace if wear is excessive. Replace the drive sprock-

et whenever you replace the chain.

Checking wear on cutting equipment

Check the chain daily for:

• Visible cracks in rivets and links.

• Whether the chain is stiff.

• Whether rivets and links are badly worn.

Replace the saw chain if it exhibits any of the points

above.

We recommend you compare the existing chain with

a new chain to decide how badly the existing chain is

worn.

When the length of the cutting teeth has worn down to

only 4 mm the chain must be replaced.

Bar

Check regularly:

• Whether there are burrs on the edges of the bar.

Remove these with a ﬁ le if necessary.

• Whether the groove in the bar has become badly

worn.

Replace the bar if necessary.

ADJUSTMENT OF DEPTH GAUGE SETTING

• The cutting teeth should be newly sharpened before

adjusting the depth gauge setting. We recommend

that you adjust the depth gauge setting every third

time you sharpen the cutting teeth.

NOTE! This recommendation assumes that the length

of the cutting teeth is not reduced excessively.

• You will need a ﬂ at ﬁ le and a depth gauge tool. We

recommend that you use our depth gauge tool to

acheive the correct depth gauge setting and bevel

for the depth gauge.

• Place the depth gauge tool over the chain. Detailed

information regarding the use of the depth gauge

tool, will be found on the package for the depth

gauge tool. Use the ﬂ at ﬁ le to ﬁ le off the tip of the

depth gauge that protrudes through the depth gauge

tool. The depth gauge setting is correct when you no

longer feel resistance as you draw the ﬁ le along the

depth gauge tool.

TENSIONING THE CHAIN

WARNING! A slack chain may jump off and

cause serious or even fatal injury.

WARNING! Always wear approved protective

gloves. Even a non-moving chain can cause

serious cuts to yourself or persons you bump

into with an exposed chain.

The more you use a chain the longer it becomes. It is

therefore important to adjust the chain regularly to take

up the slack.

Check the chain tension every time you refuel.

NOTE! A new chain has a running-in period

during which you should check the tension

more frequently.

LUBRICATING CUTTING EQUIPMENT

WARNING! Poor lubrication of cutting equip-

ment may cause the chain to snap, which

could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain

and also maintain its ﬂ ow characteristics regardless of

whether it is warm summer or cold winter weather.

Filling with chain oil

• All our chain saws have an automatic chain lubri-

cation system. On some models the oil ﬂ ow is also

adjustable.

• The saw chain oil tank and the fuel tank are de-

signed so that the fuel runs out before the saw chain

oil.

However, this safety feature requires that you use the

right sort of chain oil (if the oil is too thin it will run out

before the fuel), and that you adjust the carburetor as

recommended (a lean mixture may mean that the fuel

lasts longer than the oil) and that you also use the rec-

ommended cutting equipment (a bar that is too long will

use more chain oil).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DPC-1316 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info