Bedienungsanleitung Defort DPC-1316 (Seite 16 von 72) (Deutsch, Englisch, Französisch)

555842

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

LONG-TERM STORAGE

Empty the fuel/oil tanks in a well ventilated area. Store

the fuel in approved cans in a safe place. Fit the bar

guard. Clean the machine.

STARTING AND STOPPING

WARNING! Note the following before start-

ing: The chain brake must be engaged when

the chain saw is started to reduce the chance

of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all

covers are ﬁ tted correctly. Otherwise the clutch can

come loose and cause personal injuries. Place the ma-

chine on ﬁ rm ground. Make sure you have a secure

footing and that the chain cannot touch anything.

Keep people and animals well away from the working

area.

COLD ENGINE

Starting: The chain brake must be engaged when the

chain saw is started. Activate the brake by moving the

front hand guard forwards.

1. Air purge: Press the air purge repeatedly until fuel

begins to ﬁ ll the bulb. The bulb need not be com-

pletely ﬁ lled.

2. Choke: Pull the blue choke/fast idle lever out to the

full extent (to the FULL CHOKE position). When the

choke/ fast idle lever is pulled out to the full extent,

the correct throttle setting is set automatically.

Start throttle: The correct choke/start throttle setting

is obtained by moving the control to the choke posi-

tion.

Starting

Grip the front handle with your left hand. Hold the chain

saw on the ground by placing your right foot through

the rear handle.

3. Pull the starter handle with your right hand and pull

out the starter cord slowly until you feel a resistance

(as the starter pawls engage) then pull ﬁ rmly and

rapidly. Never twist the starter cord around your

hand.

CAUTION! Do not pull the starter cord all the

way out and do not let go of the starter handle

when the cord is fully extended. This can

damage the machine.

4. Push in the choke control to the ”1/2 choke” set-

ting as soon as the engine ﬁ res which can be heard

through a "puff" sound.

5. Keep on pulling the cord powerfully until the engine

starts. Allow engine to warm for thirty seconds, then

squeeze throttle trigger to set normal idle.

As the chain brake is still engaged the speed of the

engine must be set to idling as soon as possible, this

is achieved by quickly pressing the throttle trigger

once. This prevents unnecessary wear to the clutch,

clutch drum and brake band.

Clean the area around the fuel cap. Clean the fuel

and chain oil tanks regularly. The fuel ﬁ lter must be re-

placed at least once a year. Contamination in the tanks

causes malfunction.

Make sure the fuel is well mixed by shaking the con-

tainer before refuelling. The capacities of the chain oil

tank and fuel tank are carefully matched. You should

therefore always ﬁ ll the chain oil tank and fuel tank at

the same time.

WARNING! Fuel and fuel vapour are highly

ﬂ ammable. Take care when handling fuel and

chain oil. Be aware of the risks of ﬁ re, explo-

sion and those associated with inhalation.

FUEL SAFETY

• Never refuel the machine while the engine is run-

ning.

• Make sure there is plenty of ventilation when refuel-

ling or mixing fuel (petrol and 2-stroke oil).

• Move the machine at least 3 m from the refuelling

point before starting it.

• Never start the machine:

1 If you have spilt fuel or chain oil on the machine.

Wipe off the spillage and allow remaining fuel to

evaporate.

2 If you have spilt fuel on yourself or your clothes,

change your clothes. Wash any part of your body that

has come in contact with fuel. Use soap and water.

3 If the machine is leaking fuel. Check regularly for

leaks from the fuel cap and fuel lines.

WARNING! Never use a machine with visible

damage to the spark plug guard and ignition

cable. A risk of sparking arises, which can

cause a ﬁ re.

TRANSPORT AND STORAGE

• Always store the chain saw and fuel so that there

is no risk of leakages or fumes coming into contact

with sparks or naked ﬂ ames from electrical equip-

ment, electric motors, relays/switches, boilers and

the like.

• Always store fuel in an approved container designed

for that purpose.

• For longer periods of storage or for transport of the

chain saw, the fuel and chain oil tanks should be

emptied. Ask where you can dispose of waste fuel

and chain oil at your local petrol station.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

• The bar guard must always be ﬁ tted to the cutting

attachment when the machine is being transported

or in storage, in order to prevent accident contact

with the sharp chain. Even a non-moving chain can

cause serious cuts to yourself or persons you bump

into with an exposed chain.

• Secure the machine during transport.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Defort DPC-1316 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info