Bedienungsanleitung DeLonghi ECAM45.760 Eletta Cappuccino (Seite 15 von 20) (Englisch)

800465

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

128

• You should use De’Longhi descaler only. Using unsuitable

descaler and/or performing descaling incorrectly may re-

sult in faults not covered by the manufacturer’s guarantee.

1. Turn the appliance on and wait until it is ready for use;

2. Press the MENU/ESC button (B14) to enter the menu;

3. Press < (B4) or > (B8) (g. 9) until “Descaling” is displayed;

4. Select by pressing the OK button (B12- g. 10): the mes-

sage “Descaling Conrm?” is displayed;

5. Press the OK button again to conrm. “EMPTY DRIP TRAY”

is displayed, alternating with “REMOVE FILTER” (if the lter

is present) and “Add descaler Press OK”;

6. Empty the water tank (A16) completely and remove the

water softener lter (C4), if present. Empty the drip tray

(A12 - g. 31) and grounds container (A10), then put them

back in the appliance.

A B

7. Pour the descaler into the

tank up to level A (corre-

sponding to a 100 ml

pack) marked on the inner

surface of the tank (g.

44), then add water (1

litre) up to level B (g. 44)

and put the water tank

back.

2 l

8. Place an empty container

with a minimum capacity

of 2 litres under the coee

spouts (A7) and hot water

spout (C6) (g. 45).

Important! Danger

of burns

Hot water containing acid ows

out from the coee and hot

water spouts. Take care to avoid

contact with splashes of this

solution.

9. Press the OK button to conrm that you have added the

descaler solution. The message “Descale underway” is dis-

played and the descaling procedure begins. The descaler

liquid comes out of the coee spouts and hot water spout

and a series of rinses and pauses is performed to remove

limescale deposits from inside the machine;

After about 25 minutes, descaling stops and the messages

“RINSING” and “FILL TANK” alternate on the display;

10. The appliance is now ready for rinsing through with clean

water. Empty the container used to collect the descaler

solution. Extract the water tank, empty, rinse under run-

ning water, ll with fresh water up to the MAX level and

put back in the appliance: “RINSING, Press OK” is displayed;

11. Place the container used to collect the descaler solution

empty under the cappuccino maker (g. 45);

12. Press the OK button to start rinsing. Hot water ows out

of the spouts and the message “RINSING Please wait” is

displayed;

13. When the water tank is empty, the messages “RINSING”,

“FILL TANK” and “REPLACE FILTER” (if previously removed)

alternate on the display. Empty the container used to col-

lect the rinsing water;

14. Remove the water tank, replace the water softener lter (if

previously removed), ll the tank up to the MAX level with

fresh water and insert it in the appliance. “RINSING Press

OK” appears on the display;

15. Place the container used to collect the rinsing water empty

under the hot water spout (g. 45);

16. Press the OK button to resume rinsing. Rinsing begins

again from the hot water spout only and the message

“RINSING Please wait” is displayed;

17. When it nishes, the message “Rinsing complete, Press OK”

is displayed;

18. Press the OK button. The message “FILL TANK” is displayed;

19. Empty the drip tray, remove and top up the water tank

with fresh water to the MAX level and put back in the

machine.

Descaling is complete.

Please note!

• If the descaling cycle is not completed correctly (e.g. no

electricity) we recommend repeating the cycle;

• After descaling, it is normal for the grounds container

(A10) to contain water.

14. SETTING WATER HARDNESS

The DESCALE message appears on the display after a period of

time established according to water hardness.

The machine is set by default for a hardness value of 4. The ma-

chine can also be programmed according to the hardness of the

mains water in the various regions so that the machine needs to

be descaled less often.

14.1 Measuring water hardness

1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1)

from its pack (attached to the English instructions).

2. Immerse the paper completely in a glass of water for one

second.

3. Remove the paper from the water and shake lightly. After

about a minute, 1, 2, 3, or 4 red squares form, depending

on the hardness of the water. Each square corresponds to

one level.

14.2 Setting water hardness

1. Press the MENU/ESC (B14) button to enter the menu.

2. Press < (B4) or > (B8) (g. 9) and select “Water hardness”.

3. Conrm the selection by pressing the OK button (B12- g.

10).

4. Press < or > repeatedly to set the level as measured by the

indicator paper (see previous section).

5. Press the OK button to conrm the setting.

6. Press the MENU/ESC button to exit the menu.

The machine is now reprogrammed with the new water hard-

ness setting.

15. WATER SOFTENER FILTER

Certain models are tted with a water softener lter (C4). If this

is not the case with your model, you are recommended to pur-

chase one from De’Longhi Customer Services.

To use the lter correctly, follow the instructions below.

15.1 Installing the lter

1. Remove the lter (C4)

from the packaging.

2. Turn the date indicator

disk (see g. 46) until the

next two months of use

are displayed.

Please note

The lter lasts about two

months if the appliance is used

normally. If the coee machine

is left unused with the lter in-

stalled, it will last a maximum of three weeks.

3. To activate the lter, run tap water through the hole in the

lter as shown in the gure until water comes out of the

openings at the side for more than a minute (g. 47).

soft water

slightly hard water

hard water

very hard water

DeLonghi ECAM45.760 Eletta Cappuccino Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeLonghi ECAM45.760 Eletta Cappuccino

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info