Bedienungsanleitung DeLonghi ECAM45.760 Eletta Cappuccino (Seite 16 von 20) (Englisch)

800465

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

129

solution. Extract the water tank, empty, rinse under run-

ning water, ll with fresh water up to the MAX level and

put back in the appliance: “RINSING, Press OK” is displayed;

11. Place the container used to collect the descaler solution

empty under the cappuccino maker (g. 45);

12. Press the OK button to start rinsing. Hot water ows out

of the spouts and the message “RINSING Please wait” is

displayed;

13. When the water tank is empty, the messages “RINSING”,

“FILL TANK” and “REPLACE FILTER” (if previously removed)

alternate on the display. Empty the container used to col-

lect the rinsing water;

14. Remove the water tank, replace the water softener lter (if

previously removed), ll the tank up to the MAX level with

fresh water and insert it in the appliance. “RINSING Press

OK” appears on the display;

15. Place the container used to collect the rinsing water empty

under the hot water spout (g. 45);

16. Press the OK button to resume rinsing. Rinsing begins

again from the hot water spout only and the message

“RINSING Please wait” is displayed;

17. When it nishes, the message “Rinsing complete, Press OK”

is displayed;

18. Press the OK button. The message “FILL TANK” is displayed;

19. Empty the drip tray, remove and top up the water tank

with fresh water to the MAX level and put back in the

machine.

Descaling is complete.

Please note!

• If the descaling cycle is not completed correctly (e.g. no

electricity) we recommend repeating the cycle;

• After descaling, it is normal for the grounds container

(A10) to contain water.

14. SETTING WATER HARDNESS

The DESCALE message appears on the display after a period of

time established according to water hardness.

The machine is set by default for a hardness value of 4. The ma-

chine can also be programmed according to the hardness of the

mains water in the various regions so that the machine needs to

be descaled less often.

14.1 Measuring water hardness

1. Remove the “TOTAL HARDNESS TEST” indicator paper (C1)

from its pack (attached to the English instructions).

2. Immerse the paper completely in a glass of water for one

second.

3. Remove the paper from the water and shake lightly. After

about a minute, 1, 2, 3, or 4 red squares form, depending

on the hardness of the water. Each square corresponds to

one level.

14.2 Setting water hardness

1. Press the MENU/ESC (B14) button to enter the menu.

2. Press < (B4) or > (B8) (g. 9) and select “Water hardness”.

3. Conrm the selection by pressing the OK button (B12- g.

10).

4. Press < or > repeatedly to set the level as measured by the

indicator paper (see previous section).

5. Press the OK button to conrm the setting.

6. Press the MENU/ESC button to exit the menu.

The machine is now reprogrammed with the new water hard-

ness setting.

15. WATER SOFTENER FILTER

Certain models are tted with a water softener lter (C4). If this

is not the case with your model, you are recommended to pur-

chase one from De’Longhi Customer Services.

To use the lter correctly, follow the instructions below.

15.1 Installing the lter

1. Remove the lter (C4)

from the packaging.

2. Turn the date indicator

disk (see g. 46) until the

next two months of use

are displayed.

Please note

The lter lasts about two

months if the appliance is used

normally. If the coee machine

is left unused with the lter in-

stalled, it will last a maximum of three weeks.

3. To activate the lter, run tap water through the hole in the

lter as shown in the gure until water comes out of the

openings at the side for more than a minute (g. 47).

4847

0,5 L

4. Extract the tank (A16) from the appliance and ll with

water.

5. Insert the lter in the water tank and immerse it complete-

ly for about ten seconds, sloping it and pressing it lightly to

enable the air bubbles to escape (g. 48).

6. Insert the lter in the lter housing (A17- g. 49A) and

press as far as it will go.

7. Close the tank with the lid (A18- g. 49B), then replace the

tank in the machine.

49A 49B

When you install the lter, you must notify the appliance of its

presence.

8. Press the MENU/ESC button (B14) to enter the menu;

9. Press < (B4) or > (B8) (g. 9) until “Install lter” appears

on the display (B13).

10. Press the OK button (B12- g. 10).

11. “Install?” is displayed.

12. Press the OK button to conrm the selection. “HOT WATER

Press OK” is displayed.

13. Position a container under the hot water spout (C6) (min.

capacity: 500 ml).

14. Press the OK button to conrm the selection. The appliance

begins hot water delivery and the message “Please wait” is

displayed.

15. After the ow of hot water stops, the appliance automati-

cally resets to “Ready for coee” status.

The lter is now active and you can use the coee machine.

soft water

slightly hard water

hard water

very hard water

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeLonghi ECAM45.760 Eletta Cappuccino Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeLonghi ECAM45.760 Eletta Cappuccino

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info