Bedienungsanleitung Denon AVC-A1HD (Seite 30 von 120) (Englisch)

469386

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite



Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting

Conﬁguration

The speaker system to be measured can be selected ahead of time

here.

[Selectable items]

9.1

7.1

5.1

9.2

7.2

5.2

9.3

7.3

5.3

z1: This can be set when “Subwoofer” is set to “1SP”.

z2: This can be set when “Subwoofer” is set to “2SP L/R” or “2SP

MIX”.

z3: This can be set when “Subwoofer” is set to “3SP L/R/LFE” or

“3SP MIX”.

Start

Start Auto Setup.

The Audyssey MultEQ XT Auto Setup process automatically calculates

the size, level, distance, bass management crossover frequency, and

optimal settings for each speaker and subwoofer. Audyssey MultEQ

XT corrects acoustical distortions within the listening area.

Before starting, connect and position all your speakers.

Once started, MultEQ XT will play a series of test tones through each

speaker.

If an error message appears during the measurements, check “Error

Messages” (vpage 27), take the advised action, then start the

measurements again.

Setting the correct speaker conﬁguration can reduce the time required

to measure during the auto setup procedure as the system will not

have to look for speakers that are not connected.

STEP1 : Speaker Detection

Amp Assign

Advanced setting : changes power ampliﬁer assignment.

NOTE

The items selectable at “Conﬁguration” differ according to the “Amp

Assign” settings.

The speaker connection and polarity are detected at the ﬁrst

measurement position. The following attributes are also determined

at this time: “Speaker Size”, “Speaker Distance”, “Channel Level”,

“Crossover Frequency”.

Once the measurements are completed, the results are displayed.

NOTE

• Loud test tone may be played during Audyssey MultEQ XT Automatic

Speaker Setup. This is part of normal operation. If there is background

noise in room, these test tones will increase in volume.

• Do not stand between the speakers and setup microphone or allow

obstacles in the path while the measurements are being made. This

will cause inaccurate readings.

• Quiet the listening environment before beginning measurements and

refrain from talking. Turn off air conditioning units or other devices

that emit noise if at all possible as measurements may be affected

by these sounds.

• Operating the MASTER VOLUME knob on the main unit or the VOL

+/– buttons on the remote control unit during the measurements will

cancel the measurements.

• Do not change the speaker connections or subwoofer volume after

“STEP1”.

STEP2: Measurement

STEP3: Calculation

After completing a measurement position, move the microphone to

the next position.

Measure at least 6 positions (main listening position and at least 5 other

surrounding positions). For best results it is recommend measuring 6

or more positions (with a maximum of 8 positions).

NOTE

Do not turn the power off while the settings are being stored.

When “Calculate” is selected at “STEP2”, the measurements taken

are analyzed automatically to determine how the speaker system

interacts with the room.

The time required for this analysis depends on the number of speakers

connected. The higher the number of speakers, the longer the time

required for analysis.

STEP4: Check

Once the auto setup procedure is complete, a measuring result check

screen appears.

Select any item whose results you want to check to review the

results.

Values that are different from the actual distance may be set for

speakers with built-in ﬁlters (subwoofers, etc.). This is because ﬁlters

add electrical delay to the signal that should be compensated.

STEP5: Store

The auto setup measurement results are stored in the AVC-A1HD.

Subwoofer

The conﬁguration of the measuring subwoofer can be selected

beforehand.

[Selectable items]

1SP

2SP L/R

2SP MIX

3SP L/R/LFE

3SP MIX

Setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVC-A1HD Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVC-A1HD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info