Bedienungsanleitung Denon AVP-A1HDCI AVR-5308CI (Seite 12 von 20) (Englisch)

571792

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1

GUI Menu Map Setup Information Troubleshooting

[SAT TU]

[ AMP]

The strength of both the SIRIUS satellite and terrestrial signals can

be checked at GUI menu “Source Select” – “SIRIUS” – “Antenna

Aiming” (vpage 6).

Checking the SIRIUS Signal Strength

and Radio ID

Either turn <SOURCE SELECT> or press [SAT TU] to

select “SIRIUS”.

b When operating via the remote control unit, you cannot select

SIRIUS even by pressing [SOURCE SELECT] to which SIRIUS has

been assigned.

Press <STATUS> until “SIGNAL” appears on the

display.

The display will switch as shown below, depending on the

reception conditions.

Display Status

EXCELLENT Signal strength is excellent

GOOD Signal strength is good

WEAK Signal strength is weak

NO SIGNAL No signal

Adjust the position of the antenna until “SIGNAL:

EXCELLENT” is shown on the display.

Press <STATUS> until the channel (example: “SR001”)

is displayed.

Press [ ] and select channel 0 (SR000).

Channel No. and Sirius ID are alternately shown on the display.

S R0 0 0 Si r iu sI D

* ** * ** ** * ** *

b Write your own SIRIUS ID for storage use.

Sirius ID :

Sirius ID

Presetting Radio Channels

(Preset Memory)

Your favorite broadcast channels can be preset so that you can

tune them in easily. Up to 56 channels can be preset.

Tune in the broadcast channel you want to preset.

Press [MEMO].

Make the necessary preparations.

q Assign the SIRIUS input.

Assign the SIRIUS input.

: “Source Select” – “(input source)” – “Assign” –

“SIRIUS” (vpage 7)

w Change the TUNER(DEV2) setting on the main remote control

unit to SIRIUS.

: “Manual Setup” – “Option Setup” –

“Remote (SIRIUS/XM)” (vpage 5)

Either turn <SOURCE SELECT> or press [SAT TU] to

select “SIRIUS”.

b When operating via the remote control unit, you cannot select

SIRIUS even by pressing [SOURCE SELECT] to which SIRIUS has

been assigned.

When using the main remote control unit to operate,

press [TU] to select mode.

Use [ ] to select the channel.

When the channel is tuned in, the name of the song and artist

are displayed.

• The channel switches continuously when [ ] is pressed

and held.

• The song title, artist name, composer name, category and reception

level can be checked by pressing <STATUS>.

• The time (default : 30 sec) for which the on-screen display are

displayed can be set at GUI menu “Manual Setup” – “Option Setup” –

“GUI” – “Tuner”.

• The sub remote control unit can also be used for SIRIUS (vpage

13).

Basic Operation

There is no SIRIUS-dedicated input terminal for AVP-A1HDCI /

AVR-5308CI.

When using an audio input source not used by AVP-A1HDCI /

AVR-5308CI, assign SIRIUS to the source.

uio p

[ TU]

[MEMO]

uiop

[NUMBER

(0 ~ 9)]

[CHANNEL + –]

[SEARCH]

[ENTER]

[A ~ G]

Button located on both the main unit

and the remote control unit

BUTTON

Button only on the main unit

Button only on the remote control unit

[BUTTON]

Symbols used to indicate buttons in this manual

(AMP mode)

[ ]

(

mode)

Playback

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVP-A1HDCI AVR-5308CI Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVP-A1HDCI AVR-5308CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info