Bedienungsanleitung Denon AVR-1082 (Seite 13 von 82) (Englisch)

583778

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

ENGLISH

Once “Meter” or “Feet” is selected in Step 3,

the Delay Time screen appears automatically.

Select the speaker to be set.

BAND MODE

TUNING

Example: When the distance is set to

3.6 m for the center speaker

Set the distance between the

center speaker and listening

position.

The distance changes in units

of 0.1 meters (1 foot) each

time the button is pressed.

Select the value closest to the

measured distance.

BAND MODE

TUNING

If “Yes” is selected for “Default”, the settings are

automatically reset to the default values.

Please note that the difference of distance for every speaker

should be 4.5 m (15 ft) or less. If you set an invalid distance,

a CAUTION notice, such as screen right will appear. In this

case, please relocate the blinking speaker(s) so that its

distance is no larger than the value shown in highlighted line.

Enter the setting.

The System Setup Menu reappears.

The AVR-3802 automatically sets the optimum surround delay time for the listening room.

ENTER

SHIFT

NOTES:

• If the distance unit is changed after the delay time is set, the settings are reset to the factory default values

(see page 9).

• Use this setting to adjust so that the playback level between the different channels is equal.

• From the listening position, listen to the test tones produced from the speakers to adjust the level.

• The level can also be adjusted directly from the remote control unit. (For details, see page 27.)

• When using both surround speakers A and B, their playback levels can be adjusted separately.

Setting the channel level

At the System Setup Menu select “Channel Level”.

BAND MODE

TUNING

Switch to the Channel Level screen.

ENTER

SHIFT

Select “Test Tone Mode”.

BAND MODE

TUNING

Example: When the “Auto” mode is selected

Select the mode.

Select “Auto” or “Manual”.

• Auto:

Adjust the level while listening to the test tones produced

automatically from the different speakers.

• Manual:

Select the speaker from which you want to produce the

test tone to adjust the level.

BAND MODE

TUNING

Select “Surr. Sp.”, then select the surround speaker(s) from which

you want to produce the test tone (A, B or A+B).

• Surr. Sp.: A

Adjusts the balance of the playback level between the channels

when using surround speaker A.

• Surr. Sp.: B

Adjusts the balance of the playback level between the channels

when using surround speaker B.

• Surr. Sp.: A+B

Adjusts the balance of the playback level between the channels

when using surround speakers A and B at the same time.

The “Surr. Sp.” can only be selected when both surround

speakers A and B have been selected at the “Speaker

Configuration” (when both A and B have been set to “Large” or

“Small”).

BAND MODE

TUNING

BAND MODE

TUNING

Select “Test Tone Start”.

BAND MODE

TUNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-1082 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info