498675
13
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Getting Started Setup Playback Remote Control Information Troubleshooting
ENGLISH
w q
w q
w q w q w q w q
*/
w q w qw q
(R)
(L) (R) (L) (R)
(L) (R) (L)
Speaker Connections
Example: 7.1-channels (FRONT A+B)
Front speakers
A
Center speaker
Subwoofer
Subwoofer
with built-in
amplifier
Surround speakers
When using just one surround back speaker, connect it to the left channel (SBL).
b L : Left
R : Right
Front speakers
B
Connecting the Speaker Cables
Carefully check the left (L) and right (R) channels
and + (red) and – (black) polarities on the speakers
being connected to the AVR-1508, and be sure to
interconnect the channels and polarities correctly.
1
Peel off about 10 mm of
sheathing from the tip of the
speaker cable, then either
twist the core wire tightly or
terminate it.
2
Turn the speaker terminal
counterclockwise to loosen
it.
3
Insert the speaker cable’s
core wire to the hilt into the
speaker terminal.
4
Turn the speaker terminal
clockwise to tighten it.
NOTE
Use speakers with an impedance of 6 to 16
Ω/ohms. When using front A and B speakers
simultaneously, use speakers with an impedance
of 12 to 16 Ω/ohms.
Connect the speaker cables in such a way that
they do not stick out of the speaker terminals.
The protection circuit may be activated if the core
wires touch the rear panel or if the + and sides
touch each other (v “Protection circuit”).
Never touch the speaker terminals while the
power supply is connected. Doing so could result
in electric shock.
Protection circuit
If speakers with an impedance lower than specified
(for example 4 Ω/ohms speakers) are used for an
extended period of time with the volume turned
up high, the temperature may rise, activating the
protection circuit.
When the protection circuit is activated, the
speaker output is shut off and the power indicator
flashes red. If this happens, unplug the power
cord, then check the speaker cable and input cable
connections. If the set is extremely hot, wait for it
to cool off and improve ventilation around it. Once
this is done, plug the power cord back in and turn
the set’s power back on.
If the protection circuit is activated again even
though there are no problems in the ventilation
around the set nor in the connections, the set may
be damaged. Turn the power off, then contact a
DENON service center.
Surround back
speakers
Connections
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

denon-avr-1508

Suche zurücksetzen

  • Fernbedienung RC-1104 einrichten, wie mache ich das Eingereicht am 22-6-2021 19:17

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Denon AVR-1508 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Denon AVR-1508

Denon AVR-1508 Kurzanleitung - Deutsch - 60 seiten

Denon AVR-1508 Bedienungsanleitung - Deutsch - 60 seiten

Denon AVR-1508 Kurzanleitung - Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info