Bedienungsanleitung Denon AVR-1909 (Seite 45 von 81) (Englisch)

60741

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

A4 SB CH Out (for 2-channel sources)

Determine whether to use surround back speakers.

[Selectable items]

: The surround back channel signal is played.

OFF

: The surround back channel signal is not played.

A5 SUBWOOFER ATT

Attenuate subwoofer level when using EXT. IN mode.

[Selectable items]

: The input from the subwoofer channel is attenuated.

OFF

: The input from the subwoofer channel is not attenuated.

Usually use in this mode.

Set this to “ON” if the subwoofer channel level seems too high when

playing audio signal.

A6 Subwoofer

Turn subwoofer output on and off.

[Selectable items]

: The subwoofer is used.

OFF

: The subwoofer is not used.

Tone

Adjust the tonal quality of the sound.

Audyssey Settings

Select MultEQ, Dynamic EQ and Dynamic Volume.

Audyssey

Audyssey Byp. L/R

Audyssey Flat

ManualOFF

S0 MultEQ

Select the type of correction desired from the following list:

[Selectable items]

Audyssey

: Optimize frequency response of all speakers.

Audyssey Byp. L/R

: Optimize frequency response of speakers

except front L and R speakers.

Audyssey Flat

: Optimize frequency response of all speakers

to ﬂat response.

Manual

: Apply frequency response set with “Manual

EQ” (vpage 28).

OFF

: Turn equalizer off.

Operating from the main unit or remote

control unit

Press MULTEQ.

A7 Tone Control

Turn tone adjustments off.

[Selectable items]

: Allow tone adjustment (treble, bass).

OFF

: Playback without tone adjustment.

The tone cannot be adjusted when in the DIRECT mode.

A8 Bass

Adjust low frequency range (bass).

[Variable range]

–6dB

0dB

+6dB

A9 Treble

Adjust high frequency range (treble).

[Variable range]

–6dB

0dB

+6dB

“Bass” and “Treble” can be set when “Tone Control” is set to “ON”.

NOTE

When the “Dynamic EQ” setting is “ON”, setting is not possible.

• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is

selected, “ ” lights.

• After running Auto Setup, if the Speaker Conﬁguration, Distance,

Channel Level, and Crossover Frequency have changed without

increasing the number of speakers measured, only “ ”

lights.

• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be

selected after the auto setup procedure has been performed.

• After performing “Auto Setup”, the “MultEQ” setting automatically

becomes “Audyssey”.

• If the settings of speakers for which “None” has been determined

at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R” and

“Audyssey Flat” cannot be selected. Either perform Auto Setup

again, or return to the setting after running Auto Setup with “Auto

Setup” – “Parameter Check” – “Restore”.

• MultEQ and Manual EQ set to “Not Used” with “Manual Setup”

– “Audio Setup” – “EQ Preset” – “EQ Customize” (vpage 28) on

the menu, cannot be selected.

• When using headphones, “MultEQ” is set to “OFF”.

For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 38).



Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting

ENGLISH

Speciﬁcations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-1909 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-1909

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info