2Use [o p] to select the category, then use [ui] to
select the desired channel.
Channel category
• “UPDATING” is displayed while the encording code is being
updated.
• “SIRIUS UPDATING” is displayed when updating SIRIUS tuner
fi rmware.
• Refer to “Troubleshooting” – “SIRIUS Satellite Radio” regarding other
messages (vpage 75).
Parental Lock
1Tune to the channel you want to lock.
2Press [ENTER] for at least 3 seconds.
“Code: [ ]” is displayed.
3Enter the 4-digit lock code using uio p.
When you enter the correct code, the corresponding channel is
locked.
4Press [ENTER].
• Channels under Parental Lock cannot be tuned in by performing
Tuning Up/Down or by category search.
• Channels stored in preset memory can be tuned in by the preset
channel select operation, even if Parental Lock is applied.
• When a channel to which Parental Lock is applied is being played,
Parental Lock for that channel is cancelled by performing Step2.
• See “Edit Lock Cord” (vpage 36) for the method of changing
Parental Lock Cord.
• You can also set “Parental Lock” from the menu. (vpage 36).
iPod® Playback
The music on an iPod can be played by using the control dock for
iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold separately).
The operation can also be performed using the buttons on the main
unit or remote control unit while watching the menus.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
1Make the necessary preparations.
q Set the iPod in the DENON control dock for iPod.
(vSee the control dock for iPod’s operating instructions.)
w Assign the control dock for iPod’s input.
The input for the control dock for iPod is assigned to VCR by
default.
MENU : ”Input Setup” – “Assign” – ”iPod Dock”
(vpage 35)
2Either turn <SOURCE SELECT> or press [iPod] to
select the input source assigned in step 1-w above.
(iPod screen)
b If the screens above are not displayed, the iPod may not be
properly connected. Try connecting again.
3Set [SOURCE CONTROL 1] to “AUDIO” and [SOURCE
CONTROL 2] to “iPod/NETWORK”.
(vpage 57 “Remote Control Unit Operations”)
Basic Operation
OK to disconnect.
• With the default settings, the iPod can be used connected to the
VCR (iPod) connector.
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio fi les and achieve a richer sound.
The default setting is “Mode3” (vpage 44).
• Press <ON/STANDBY> or [OFF] and set the AVR-2309CI’s power to
the standby mode before disconnecting the iPod. Also switch the
input source to one to which the menu “iPod Dock” is not assigned
before disconnecting the iPod.
• When using an ASD-3N or ASD-3W control dock for iPod, refer to
the respective manual to operate.
4Press [MODE] and hold it down for a 2 seconds or
more to select the display mode.
To switch between modes, press and hold down the button.
When remote mode is active, “Remote” is displayed.
[Selectable mode] Browse mode Remote mode
Display location Main unit display
iPod display
Playable
files
Audio file S S
Video file S
z1
S
z2
Active
buttons
Remote
control unit
(AVR-2309CI)
S S
iPod A S
z
1 :
When using an ASD-3N or ASD-3W control dock for iPod.
z
2 : Video may not be output, depending on the combination of
ASD-1R or ASD-11R and iPod.
Playback
