Bedienungsanleitung Denon AVR-2808CI (Seite 28 von 96) (Englisch)

584190

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Error Messages

If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is

displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the auto setup procedure over

again.

Error messages (examples) Cause Measures

Retry

Cancel

Microphone:None

Speaker :None

Auto Setup

Caution!

• Included setup microphone is not connected.

• Not all speakers could be detected.

• Connect the included setup microphone to the SETUP

MIC jack on the main unit.

• Check the speaker connections.

too high or

Retry

Cancel

Ambient noise is

Level is too low.

Auto Setup

Caution!

• Too much noise in the room for accurate

measurements to be made.

• Speaker or subwoofer sound is too low for

accurate measurements to be made.

• Either turn off any device generating noise or move it

away.

• Try again when the surroundings are quiet.

• Check the speaker installation and the direction in

which the speakers are facing.

• Adjust the subwoofer’s volume.

Retry

L :None

Cancel

Skip

Front

Auto Setup

Caution!

• Displayed speaker could not be detected.

· The front L and front R speakers were not

properly detected.

· Only one channel of the surround speakers

was detected.

· Sound was output from the R channel

when only one surround back speaker was

connected.

· The surround back, but the surround speaker

was not detected.

• Check the connections of the displayed speaker.

Retry

L :Phase

Cancel

Skip

Front

Auto Setup

Caution!

• Displayed speaker connected with the

polarities reversed.

• Check the polarities of the displayed speaker.

• For some speakers, this error message may be

displayed even if the speaker is properly connected. In

this case, select “Skip”.

NOTE

Be sure to turn the power off before checking the speaker connections.

Room EQ

Select room EQ setting method.

[Selectable items]

All

: Apply settings to all surround modes.

Assign

: Make settings for each surround mode separately.

Option

Select settings for room EQ, mic, etc.

Select “Retry” to make the measurements again.



Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

Direct Mode Setup

Select room EQ use for DIRECT or PURE DIRECT mode.

[Selectable items]

: Use room EQ.

OFF

: Do not use room EQ.

Mic Select

Select the microphone type if not using supplied mic.

The microphone connected to V.AUX Lch is used.

[Selectable items]

Mic

: Supplied mic is being used.

V.AUX L

: Other mic connected to V.AUX is used.

Parameter Check

Check auto setup measurement results.

This is displayed after the auto setup procedure is completed.

[Items to be checked]

Speaker Conﬁg. Check

Distance Check

Channel Level Check

Crossover Freq. Check

EQ Check

The auto setup results can be set again when “Restore” is selected.

AVR2808CIEU.indd 28 2007/06/20 8:58:01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-2808CI Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-2808CI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info