Bedienungsanleitung Denon AVR-590 (Seite 49 von 67) (Englisch)

455822

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

4

ENGLISH

Getting Started

Connections Playback Information Troubleshooting

Speciﬁ cationsSettings

Switch to the device to be operated.

TUNER/AMP

: To operate a Tuner

DEVICE

: To operate a Blu-ray disc player, DVD player,

CD player,

Digital video recorder, Video deck,

iPod, Satellite receiver or cable TV

MAIN/TV

: To operate a TV

When “DEVICE” has been selected in step 1, press

the source select button for the device to be operated.

The remote control unit is set to the device mode for the device

to be operated. When the remote control transmitter is pointed

towards the AVR-590 at this time, the AVR-590’s input source

switches simultaneously.

b The remote control unit stays in the same device mode until a

different source select button is pressed.

Operate the component.

b For details, refer to the component’s operating instructions.

Operating the Connected Devices by Remote Control Unit

• Some manufacturers use more than one type of remote control code.

Refer to the included list of preset codes to change the number and

verify correct operation.

• The preset memory can be set for one component only among the

following: DVD/CD and SAT/CBL.

Registering Preset Codes

DENON and other makes of components can be operated by

setting the preset memory.

Operating Registered Devices

NOTE

Depending on the model and year of manufacture, this function cannot

be used for some models, even if they are of makes listed in the list

of preset codes.

Operation

mode setting

ON/SOURCE

Power on / Standby

z

Play / Pause

Stop

Pause

MEMORY

TOP MENU

Calling out the top menus

6 7

Manual search

(fast-reverse / fast-forward)

8 9

Auto search

(cue)

uio p

Cursor

ENTER Enter

Press and

hold

Once

Browse/Remote

mode switching

Page search

mode switching

RETURN Return

PAGE d f

Page up/down

z

1 : This operation is possible when using a

DENON ASD-3N or ASD-3W Control Dock

for iPod.

2 : This operation is possible when using a

DENON ASD-1R or ASD-11R Control Dock

for iPod.

iPod

Operating Registered Devices

Press the source select button (see

below) for the device to be registered

and simultaneously for over 2

seconds.

“RC SETUP START” appears on the display

and the remote control unit is set to the

preset code registration mode.

: TV : Digital video recorder

DVD player

or CD player

: Video deck

: Blu-ray disc player

Satellite receiver

or cable TV

Press ~ and input the

3-digit number of the brand of

the component to be preset. The

numbers are shown in the Preset

Code Table (vEnd of this

manual).

When registration is completed, “RC SETUP OK” appears on

the display.

b If the codes could not be registered, “RC SETUP NG” appears on

the display. Try again.

To store the codes of another component in the

memory, repeat steps 1 to 2.

b For details, refer to the component’s operating instructions.

n Cautions during operation

When registering a preset code, point the remote control transmitter

toward the AVR-590. The status of the registration operation is

displayed on the AVR-590.

Remote Control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-590 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-590

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info