Bedienungsanleitung Denon DN-X300 (Seite 6 von 17) (Englisch, Spanisch)

614632

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

ENGLISH

!7 Input select switch

• Switches between the PHONO/LINE and LINE

inputs.

• When the lever of switch is vertical position, the

LINE2 or LINE4 input is selected.

• When the lever of switch is slope, the

PHONO1/LINE1 or PHONO2/lINE3 input is

selected.

• You can perform 8 direction placement. See

page 10.

!8 SPLIT CUE button

• In the STEREO mode, the stereo sound of

MASTER and CUE are fed to both ear cups. In

the SPLIT CUE mode, the headphone circuit

provides monaural CUE sound to the left and

monaural MASTER sound to the right.

• When the Level Meter mode select switch is

set to “MASTER”…In the STEREO mode, the

meter indicates the stereo level in the L/R

Master output. In the SPLIT CUE mode, the

monaural CUE sound level is displayed on the

left and the monaural MASTER sound level is

displayed on the right.

• In the SPLIT CUE mode, the LED is lit.

!9 PGM 1/2 KILLS switches

• These switches are used cut out the Treble, Mid

or Bass frequencies of the incoming audio

signal. When these switches moved up or

down, the selected frequency level is cut, the

LED located directly above the specific switch

will glow indicating the cut function has been

activated.

@0 Level meter mode select switch

• The position of this switch will determine the

Level Meter mode. In the “MASTER” position,

the meter will detail the out level of the left and

right channels. In the “PGM 1/2” position, the

left side of the meter will indicate monaural

level of the PGM 1 and the right side of the

meter will indicate monaural level of the PGM 2.

@1 Channel Fader

• Controls the channel output level.

@2 Level meter

• The dual LED's indicators are used to detail

either the master output level, a combination of

the master output level and the CUE signal

level, or the PGM1/2 monaural level.

@3 Crossfader

• Fades the overall mixer output between

channels 1 and 2.

(2) Rear panel

@4 Power operation switch (POWER)

• Selects power “ON” or “OFF”.

NOTE:

Whenever the power switch is in the OFF state,

the AC adaptor is still connected on AC line

voltage. Please be sure to unplug the cord when

you don’t use for along time.

@5 BALANCED MASTER OUT jacks

• These 1/4” TRS jacks provide a balanced line

level output.

• Connect these jacks to the balanced analog

input jacks on an amplifier or console.

• Pin layout: Tip=Hot Ring=Cold Sleeve=GND

@6 EFFECT LOOP SEND/RETURN jacks

• These 1/4” TS stereo jacks allow external

processing of the program signal.

• When connect monaural type effect processor,

use Lch input and output.

@7 MIC BALANCED INPUT jack

• Accepts an balanced microphone with 1/4” TRS

mono jacks.

• Pin layout: Tip=Hot Ring=Cold Sleeve=GND

@8 MIC EFFECT LOOP jack

• These 1/4” TRS jack allow external processing

of the program signal.

• Pin layout:

Tip=SEND Ring=RETURN Sleeve=GND

@9 PGM1, 2 FADER output jacks

• Connect these jacks to the FADER input jacks of

DN-S3000, DN-S5000, DN-S1000 and etc. using

the 3.5mm stereo mini cord.

#0 Phono ground screw (GND)

• This screws provide a place to connect the

ground wire from a turntable.

• This terminal is exclusively for a turntable

ground and not a safety earth ground.

#1 PHONO1, 2 / LINE1, 3 switches

(LN / PH)

• These switches change the input from PHONO

to a LINE level input.

• These switches set a LINE level input when

turntable is not connected.

NOTE:

Always be sure main power is shut off before

change the position of the Line Level Selector

Switch.

#2 PHONO1, 2 / LINE1, 3 input jacks

• These stereo pairs of unbalanced RCA jacks are

inputs for a PHONO (RIAA) stage for magnetic

(MM) cartridges or a LINE stage suitable for any

device, such as a CD player.

#3 LINE2, 4 input jacks

• These stereo pairs of unbalanced RCA jacks are

inputs for any line level device.

#4 AUX INPUT jacks

• This stereo pair of RCA jacks provides an

unbalanced line level input with independent top

panel AUX INPUT control.

• This input is mixed after the Crossfader and

EFFECT LOOP.

#5 BOOTH OUT jacks

• This stereo pair of RCA jacks is the same as the

MASTER output with independent BOOTH

LEVEL control.

• This output may be for recording, booth/zone

monitoring, or for connecting to another mixer.

#6 UNBALANCED MASTER OUT jacks

• This stereo pair of RCA jacks provides an

unbalanced line level output.

• Connect these jacks to the unbalanced analog

input jacks on an amplifier or console.

#7 AC IN

• Input connection for the included AC adaptor.

NOTE:

Use specified attached AC adaptor only.

(3) Front panel

#8 CH 1/2 FADER START switches

• Use this to switch the Channel Fader Start

function ON and OFF.

#9 CROSSFADER START A, B switches

• Use this to switch the Crossader Start function

ON and OFF.

$0 HEADPHONE output jack

• Accept 1/4” stereo headphone plugs.

$1 CH 1/2 FADER CONTOUR

adjustment

• Adjusts the curve of the CH1/2 faders between

fast, normal , or slow fade.

$2 CH 1/2 FADER REVERSE switch

• Reverses the direction of each respective input

CH1/2 fader.

$3 CROSSFADER CONTOUR

adjustment

• Adjusts the shape of the crossfader curve from

a fast cut for scratching or to a slow fade for

mixing.

$4 CROSSFADER REVERSE switch

• Reverses the direction of the crossfader.

Denon DN-X300 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info