Bedienungsanleitung Denon POA-3012CI (Seite 20 von 23) (Englisch)

584590

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite



Setup

ENGLISH

Other Operations

NOTE

• When the “POWER CONFIGURATION” is set to “MASTER

TRIGGER”, the device will automatically enter the standby status

when no trigger input is detected for a period of 10 minutes.

• When the “POWER CONFIGURATION” is set to “ON LINE”, send

a standby command to the ETHERNET terminal or the RS-232C

terminal of the POA-3012CI.

• Power continues to be supplied to some of the circuitry even when

the power is in the standby mode. When leaving home for long

periods of time or when traveling, unplug the power cord from the

power outlet.

Check the Status of Each

Channel

1Press the DISPLAY button.

b Zone status is indicated on the bottom line of the display.

b Turn the SELECT / ENTER knob to change the display as follows.

VOLUME CONTROL level

LOW CUT FILTER

Channel No. & INPUT Line

ZONE T.ON MODE

2Press the DISPLAY button again.

b System status is indicated on the bottom line of the display.

b Turn the SELECT / ENTER knob to change the display as follows.

POWER CONFIG DIMMER

n To Return to the Regular Display

Press the u / RETURN button until the display returns to normal.

Other Operations During Playback

n To Adjust the Volume

Refer to “VOLUME CONTROL” on the “Main Setup” menu

(vpage 13).

n To Reduce the Low Frequency Volume

Refer to “LOW CUT FILTER” on the “Main Setup” menu (vpage

13).

n To Switch Input Setting

Refer to “INPUT SELECT” on the “Main Setup” menu (vpage

13).

Operating the POA-3012CI Using a

Browser (Web control)

This function lets you operate the POA-3012CI using Internet

Explorer.

1Check the POA-3012CI’s IP Address.

“Network Setup” – “Network Information” (vpage 14)

2Input the POA-3012CI’s IP Address in Internet

Explorer.

For example, if the IP address is “10.3.18.90”, enter

http://10.3.18.90.

3If the top menu is displayed, click “Setup Menu”.

4When the “Setup Menu” is displayed, click on the

menu you want to operate.

Turning the Power On

Press the ON / STANDBY button.

The power indicator ﬂ ashes green and the power turns on.

b The signal input to each channel is output from the speaker

terminal of each channel.

b The setting status of each channel is indicated on the display.

b Turn the SELECT/ENTER knob to change the channel displayed.

CH 1&2

BTL

BUS L+R

0.0dB

Output channel Input terminal

OPERATION MODE

(No display when in “NORMAL MODE”)

Volume level

n To return to STANDBY

Press the ON / STANDBY button again.

The power indicator lights red.

DISPLAYZONE 5

ON/STANDBY

SELECT/ENTER

u/ RETURN

ZONE operation mode indicators

Click

Setup

Click the menu

CHANNEL SETUP (vExample : 1)

SYSTEM SETUP (vExample : 2)

WARNING AND PROTECTION DATA

(vExample : 3)

AUDIO SIGNAL AND TRIGGER

INPUT (vExample : 4)

OPTION SETUP (vExample : 5)

Click “SAVE” when you want to save settings,

and click “LOAD” when you want to call settings.

Becomes each operation screen.

Operations

Getting Started Connections Troubleshooting Speciﬁ cationsOperations

1.POA-3012CI_ENG_101.indd 17 2008/07/30 14:08:30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon POA-3012CI Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info