Bedienungsanleitung Denver MRP-161 (Seite 27 von 73) (Alle Sprachen)

695741

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

EN-2

3. The LCD display (2) will display the first & second digit of “ 00 ” is flashing. Press skip up or skip down button (25,12) to

set the correct hour. Press “ Mem/Clk-adj ” button (14) to store the correct hour.

4. The third & fourth digit of “ 00 ” is flashing, press the skip up or skip down button (25,12) to set the correct minutes.

Then press “ Mem/Clk-adj ” button (14) to store the correct minute.

Listening to radio

Manual tuning

1. Tune on the unit by press power On/Standby button (7)

2. Press Function button (10) to select “ Tuner ” mode.

3. Tune to the required station by pressing the skip up or skip down button (25,12).

4. Adjust volume up/down button (14) to the desired volume level.

Auto tuning

1. Press Function button (10) to select “ Tuner ” mode.

2. Press and hold the skip up/down button (25,12) for 1-2 seconds and then release.

3. The unit will start seeking automatically and stop until a radio station is reached.

4. Repeat step 2 until the desired radio station is being reached.

5. Adjust volume up/down button (3) to the desired volume level.

Preset stations

You can store up to 10 radio stations in the memory (10 FM).

1. Set to tuner mode.

2. Turn to the desired radio station by “ manual” or “ auto ” tuning method.

3. Press “ Mem/Clk-adj ” button (14) to enable program function & “ MEM ” icon and preset station nr will flash on LCD display (2)

4. Press “ Pre-up or Pre-dn ” button (26,13) to select the desired station memory for storage.

5. Press “ Mem/Clk-adj ” button (14) again to confirm the setting.

6. Repeat step 2 to 5 to store other stations.

7. Now you can select the presets stations in order by pressing the “Pre–up ” button (26) or Pre-dn button (13).

 The pre-set memories will be cancelled completely if dis-connecting the main power supply. You are recommended to

switch the system into standby mode for convenience usage.

 There are 10 seconds for program state, after 10 sec. This state would resume to normal tuner mode automatically.

 You can overwrite a present station by storing another frequency in its place.

FM & FM-stereo reception

 Press the “ St/Mono ” button (8) repeatedly, the FM programs are receiving in mono and stereo mode repeatedly. In particular

when stereo signals are weak. It is preferable to receive the program in mono.

 If stereo signal is being received, the stereo indicator “ ” will appear on LCD display (2) to show FM stereo program is now

receiving.

Hints for best reception:-

- FM : the receiver has a build-in FM wire antenna (34) hanging at the back of the unit. This wire should be totally unraveled and

extended for the best reception.

Phono

noted:

- Remove the stylus protector.

- Be sure that the tone arm is being detached from the tone arm rest before operating and re-secured again afterwards.

Press Function button (10) to select “ Phono ” mode.

1. Set the speed selector (30) to the proper position depending on the type of record to be played.

2. Place the record on the platter (use the spindle adaptor (29) if required).

3. Lift the tone arm from the pick up holder (31) and slowly move it to the record side. The platter will

start to rotate.

4. Place the tone arm to the desired position of the record.

5. Adjust the Volume up/down button (3) to the desired level.

6. At the end of record, the platter will automatically stop rotating. Lift the tone arm from the record and

return it to the rest position (31).

7. To stop intermediate, lift up the tone arm from the record and return it to the rest (31).

Remark : As some kind of record the auto-stop area was out of the unit setting, so it will stop before the last

track finish. In this case, select the auto-stop switch (33) to “ off ”position, then it will run to the end of the

record but will not stop automatically (turn off the unit by power button or switch back the auto-stop switch (33)

to “ on ” position to stop the platter rotate). Then put back the tone arm to the rest position (31).

Playing compact disc

 Getting start

1. Press Function button (10) to select “ CD ” mode.

2. Press “ Open/Close ” button (24) to open the CD tray (17).

3. Place a CD with the printed side facing up inside the tray & then close the CD tray.

4. Focus search is performing, then will start the playback automatically.

 Play / pause mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denver MRP-161 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denver MRP-161

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info