Bedienungsanleitung DeWalt D 28065 (Seite 27 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

79226

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

l) Do not run the power tool while carrying

it at your side. Accidental contact with the

spinning accessory could snag your clothing,

pulling the accessory into your body.

m) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powered metal may cause electrical hazards.

n) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

o) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Safety Warnings Speciﬁ c for

Grinding and Abrasive Cutting-off

Operations

a) Use only wheel types that are

recommended for your power tool and the

specific guard designed for the selected

wheel. Wheels for which the power tool was

not designed cannot be adequately guarded

and are unsafe.

b) The guard must be securely attached

to the power tool and positioned for

maximum safety, so the least amount of

wheel is exposed towards the operator. The

guard helps to protect operator from broken

wheel fragments and accidental contact with

wheel.

c) Wheels must be used only for

recommended applications. For example:

do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these

wheels may cause them to shatter.

d) Always use undamaged wheel flanges

that are of correct size and shape for your

selected wheel. Proper wheel flanges support

the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be

different from grinding wheel flanges.

e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power

tool is not suitable for the higher speed of a

smaller tool and may burst.

Causes and Operator Prevention

of Kickback

• Kickback is a sudden reaction to a pinched,

bound or misaligned wheel, wire brush or flap

disc causing an uncontrolled cut-off tool to

lift up and out of the workpiece toward the

operator.

• When the wheel is pinched or bound tightly by

the workpiece, the wheel stalls and the motor

reaction drives the unit rapidly back toward or

away from the operator.

• Kickback is the result of tool misuse and/or

incorrect operating procedures or conditions

and can be avoided by taking proper

precautions as given below:

• Maintain a firm grip with both hands on

the unit and position your body and arm

to allow you to resist kickback forces.

Kickback forces can be controlled by the

operator, if proper precautions are taken.

• When wheel is binding, or when

interrupting a cut for any reason, release

the trigger and hold the unit motionless

in the material until the wheel comes to a

complete stop. Never attempt to remove

the unit from the work or pull the unit

backward while the wheel is in motion or

kickback may occur. Investigate and take

corrective actions to eliminate the cause of

wheel binding.

• When restarting a cut-off tool in the

workpiece, check that the wheel is not

engaged into the material. If wheel is

binding, it may walk up or kickback from the

workpiece as the tool is restarted.

• Support large panels to minimise the risk

of wheel pinching and kickback. Large

panels tend to sag under their own weight.

Support must be placed under the panel on

both sides, near the line of cut and near the

edge of the panel.

LABELS ON TOOL

In addition to the pictographs used in this

manual, the labels on the tool show the following

pictographs:

Read instruction manual

before use.

Wear safety glasses.

Wear ear protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28065 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info