Bedienungsanleitung DeWalt D 28065 (Seite 29 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

79226

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

The minimum conductor size is 1.5 mm

. When

using a cable reel, always unwind the cable

completely. Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 – 2.0 6 6 6 6 6 10

2.1 – 3.4 6 6 6 6 6 15

3.5 – 5.0 6 6 10 15 20 20

5.1 – 7.0 10 10 15 20 20 25

7.1 – 12.0 15 15 20 25 25 –

12.1 – 20.0 20 20 25 – – –

230 0 – 2.0 6 6 6 6 6 6

2.1 – 3.4 6 6 6 6 6 6

3.5 – 5.0 6 6 6 6 10 15

5.1 – 7.0 10 10 10 10 15 15

7.1 – 12.0 15 15 15 15 20 20

12.1 – 20.0 20 20 20 20 25 –

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always turn tool off and

disconnect tool from power source

before making any adjustments or

removing/installing attachments or

accessories. Before reconnecting the

tool, depress and release the trigger

switch to ensure that the tool is off.

Attaching side handle

Screw the side handle (g) tightly into one of the

holes (h) on either side of the gear case.

Mounting Guard

MOUNTING AND REMOVING GUARD (FIG. 2)

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure

that the tool is off.

CAUTION: Guards must be used with

this grinder.

1. Place the angle grinder on a table, spindle up.

2. Release the clamping lock (l) and hold the guard

(e) over the tool as shown.

3. Align the lugs (m) with the notches (n).

4. Press the guard down and rotate it to the

required position.

5. If required, increase the clamping force

bytightening the screw (o).

6. Tighten the clamping lock (l) .

7. To remove the guard, release the clamping lock

CAUTION: If the guard cannot be

tightened by the adjusting clamp, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service center to repair or replace

the guard.

CAUTION: To reduce the risk of

damage to the tool, do not tighten the

adjusting screw with the clamp lever

in the open position. Undetectable

damage to the guard or the mounting

hub may result.

OPERATION

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure

that the tool is off.

Trigger switch (Fig. 3)

CAUTION: Hold the side handle and

body of the tool firmly to maintain

control of the tool at start up and during

use and until the wheel or accessory

stops rotating. Make sure the wheel has

come to a complete stop be fore laying

the tool down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28065 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info