Bedienungsanleitung DeWalt D 28065 (Seite 30 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

79226

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

NOTE: To reduce unexpected tool movement,

do not switch the tool on or off while under load

conditions. Allow the grinder to run up to full speed

before touching the work surface. Lift the tool from

the surface before turning the tool off. Allow the tool

to stop rotating before putting it down.

1. To turn the tool on, depress the trigger switch

(a) while depressing the lock-off button (c).

2. Turn the tool off by releasing the trigger switch.

LOCK-ON BUTTON

The lock-on button (b) offers increased comfort

in extended use applications. To lock the tool on,

depress the trigger switch (a), then push the lock-

on button (b). The tool will continue to run after

the trigger switch is released. To unlock the tool,

depress and release the trigger switch. This will

cause the tool to stop.

CAUTION: Hold the side handle and

body of the tool firmly to maintain

control of the tool at start up and during

use and until the wheel or accessory

stops rotating. Make sure the wheel has

come to a complete stop be fore laying

the tool down.

CAUTION: Allow the tool to reach full

speed before touching tool to the work

surface. Lift the tool from the work

surface before turning the tool off.

SPINDLE LOCK

The spindle lock (d) is provided to prevent the

spindle from rotating when installing or removing

wheels. Operate the spindle lock only when the tool

is turned off, unplugged from the power supply, and

has come to a complete stop.

CAUTION: To reduce the risk of

damage to the tool, do not engage the

spindle lock while the tool is operating.

Damage to the tool will result and

attached accessory may spin off

possibly resulting in injury.

To engage the lock, depress the spindle lock button

and rotate the spindle until you are unable to rotate

the spindle further.

Fitting and removing a grinding or

cutting disc (ﬁ g. 4, 5)

1. Place the tool on a table, guard up.

2. Fit the backing flange (j) correctly onto the

spindle (q) (fig. 4).

3. Place the disc (p) on the backing flange (j).

When fitting a disc with a raised center, make

sure that the raised centre ) is facing the

backing flange (j).

4. Screw the threaded clamp nut (i) onto the

spindle (q) (fig. 5):

a. The ring on the threaded clamp nut (i) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (i) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (d) and rotate the

spindle (q) until it locks in position.

6. Tighten the threaded clamp nut (i) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (i) with the two-pin spanner.

METAL APPLICATIONS

• When using the tool in metal applications, make

sure that a residual current device (RCD) has

been inserted to avoid residual risks caused by

metal swarf.

• If the power supply is shut off by the RCD, take

the tool to authorised D

EWALT repair agent.

WARNING: In extreme working

conditions, conductive dust can

accumulate inside the machine housing

when working with metal. This can result

in the protective insulation inthe machine

becoming degraded with a potential risk

of an electrical shock.

To avoid build-up of metal swarf inside the machine,

we recommend to clear the ventilation slots on a

daily basis. Refer to Maintenance.

USING FLAP DISCS

WARNING: Metal dust build-up.

Extensive use of flap discs in metal

applications can result in the increased

potential for electric shock. To reduce

this risk, insert an RCD before use

and clean the ventilation slots daily by

blowing dry compressed air into the

ventilation slots inaccordance with the

below maintenance instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28065 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info