Bedienungsanleitung DeWalt D 28492 (Seite 26 von 105) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

78707

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

ENGLISH

Always ensure that the cable clamp is

correctly and securely ﬁ tted to the

sheath of the cable.

Assembly and adjustment

Prior to assembly and adjustment

always unplug the tool.

Mounting and removing the guard (ﬁ g. B)

● Place the angle grinder on a table, spindle up.

● Align the lugs (7) with the notches (8).

● Press the guard (5) down and rotate it to the

required position.

● Securely tighten the screw (9).

● To remove the guard, slacken the screw.

Never use the tool without the guard in

place.

Fitting and removing a grinding or cutting disc

(ﬁ g. C1 & C2)

● Place the tool on a table, guard up.

● Fit the inner ﬂ ange (10) correctly onto the

spindle (11) (ﬁ g. C1).

● Place the disc (12) on the ﬂ ange (10).

When ﬁ tting a disc with a depressed centre,

make sure that the depressed centre (13) is

facing the ﬂ ange (10).

● Screw the outer ﬂ ange (14) onto the spindle (11)

(ﬁ g. C2):

- the ring on the ﬂ ange (14) must face towards

the disc when ﬁ tting a grinding disc (A);

- the ring on the ﬂ ange (14) must face away

from the disc when ﬁ tting a cutting disc (B).

● Press the spindle lock (4) and rotate the spindle

(11) until it locks in position.

● Tighten the ﬂ ange (14) with the two-pin spanner

supplied.

● Release the spindle lock.

● To remove the disc, loosen the ﬂ ange (14) with

the two-pin spanner.

Do not use a damaged disc.

Fitting a wire cup brush

● Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded ﬂ ange.

Mounting the side handle (ﬁ g. D)

● Screw the side handle (6) tightly into one of the

holes (15) on either side of the gear case.

Holding the tool (ﬁ g. E)

● Hold the tool as shown.

● For your own safety, always use the

tool with both hands.

● Always wear regular working gloves

while operating this tool.

● Warning: The gear case becomes very

hot during use.

Instructions for use

● Always observe the safety instructions

and applicable regulations.

● Ensure all materials to be ground or cut

are secured in place.

● Apply only a gentle pressure to the tool.

Do not exert side pressure on the

grinding wheel or cutting disc.

● Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

● Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

● Be sure the inner and outer ﬂ ange are mounted

correctly.

● Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

Switching on and off (ﬁ g. A)

The on/off switch is equipped with an unlocking

switch or a locking switch for continuous operation.

On/off switch (1) with locking switch (2)

● To run the tool, depress the unlocking switch (3)

and subsequently operate the on/off switch (1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28492 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D 28492

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info