Bedienungsanleitung DeWalt D21583K (Seite 36 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544690

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Speciﬁ c Safety Rules for

Diamond Drills

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Hold power tools by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the tool “live” and shock the

operator.

• Use auxiliary handles supplied with the

tool. Loss of control can cause personal

injury.

• Wear safety goggles or other eye

protection. Drilling operations cause chips to

fly. Flying particles can cause permanent eye

damage.

• Bits, tools and drilling area get hot during

operation. Wear gloves when touching

them.

• Use the diamond drill under constant

supervision.

• Make sure not to cut through electric mains,

gas or water pipes. Use detection systems

prior to drilling.

• Make sure the cutting accessory is fitted

properly.

• Check all screws and tighten securely before

you use the machine.

• When drilling downward, make sure the core

can drop safely without injuring someone

standing beneath.

• Do not perform overhead (upward) drilling

without the use of suitable protection

shielding (water collecting device).

• When drilling handheld, always use the side

handle and hold the machine firmly with both

hands.

• Make sure to stand on a stable surface and

keep body balance at all times for better

control of reaction torque.

• Inspect the machine before every use. Do not

use the machine if there are any defectives

on the mains plug, power cord, trigger switch

or any part of the housing. Have the machine

repaired by an authorized repair agent.

• Do not use the machine in a damp or wet

location.

• Switch off the machine immediately if there is

any leak of water.

• After interrupting the cut, do not switch on

until the core bit can rotate freely.

• Always trigger off the switch to prevent the

machine from accidentally self starting.

Note this procedure especially after the

power supply is interrupted or the plug is

disconnected from the power outlet.

• Mounting the tool onto a stand is

recommended to increase the user comfort

and reduce the risk of injuries.

• Use auxilary handles supplied with the tool.

• Loss of control can cause personal injury.

• Hold power tool by insulated gripping

surfaces, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make

exposed metal parts of the power tool "live"

and shock the operator.

• In case of jammed core bit disconnect the

machine from the power supply, remove

the reason for the jam before turning on the

machine again.

DRY DRILLING

• Dry drilling is suitable for masonry

(bricks, breeze blocks).

• Always use a suitable dust extractor.

• Always use core bits designed for dry drilling.

• Do not use the machine handheld with core

bits larger than 100 mm.

• Always mount the drill on a stand when

drilling holes larger than 100 mm.

• Wear a dust mask when performing dry cuts.

D21583 - WET DRILLING

• Wet drilling is suitable for stone and concrete.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D21583K Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info