Bedienungsanleitung DeWalt d23551 (Seite 38 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383807

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ENGLISH

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Depth of Cut Adjustment (ﬁ g. 1, 2)

1. Loosen the depth adjustment knob (q).

2. Move the shoe (f) to obtain the correct depth of

cut.

3. Tighten the depth adjustment knob (q).

WARNING: For optimal results, allow

the saw blade to protrude from the

workpiece by about 5 mm (fig. 2).

Bevel Adjustment (ﬁ g. 1, 3)

The bevel angle can be adjusted between 0° and

the maximum setting.

1. Loosen the bevel adjustment knob (k).

2. Set the bevel angle by tilting the saw shoe (f)

until the mark indicates the desired angle on the

scale.

3. Tighten the bevel adjustment knob (k).

Shoe Adjustment for 90° Cuts (ﬁ g. 1)

1. Adjust the saw to 0° bevel.

2. Retract the blade guard using the lever (h) and

place the saw on the blade side.

3. Loosen the bevel adjustment knob (k).

4. Place a square against the blade and shoe to

adjust the 90° setting.

5. Tighten the bevel adjustment knob (k).

Replacing the Saw Blade (ﬁ g. 1, 4)

1. Engage the blade lock button (d) and unscrew

the blade clamping screw (s) by turning

anticlockwise using the hex wrench supplied

with the tool.

2. Retract the lower blade guard (i) using the

lever (h) and replace the blade (j). Reinstall the

washers (t, u) in the correct position.

3. Check the direction of rotation of the blade.

4. Thread on the blade clamping screw (s) by hand

to hold the washer in position. Turn clockwise.

5. Press the blade lock button (d) while turning the

spindle until the blade stops rotating.

6. Tighten the blade clamping screw firmly using

the wrench.

Adjusting the Riving Knife (ﬁ g. 4)

For the correct adjustment of the riving knife (g),

refer to figure 4. Adjust the clearance of the riving

knife after changing the saw blade or whenever

necessary.

1. Adjust the depth of cut to 0 mm to access the

clamping screws (v) of the riving knife (g).

2. Loosen the screws (v) and pull out the riving

knife to its maximum length.

3. Adjust the clearance and tighten the screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt d23551 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info