Bedienungsanleitung DeWalt d23551 (Seite 39 von 160) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383807

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

ENGLISH

Mounting and Adjusting the Parallel

Fence (D23651, ﬁ g. 5)

The parallel fence (r) is used for cutting parallel to the

edge of the workpiece.

MOUNTING

1. Slacken the fence adjustment knob (l) to allow

the parallel fence to pass.

2. Insert the parallel fence (r) in the saw shoe (f) as

shown.

3. Tighten the fence adjustment knob (l).

ADJUSTING

1. Slacken the fence adjustment knob (l) and set

the parallel fence (r) to the desired width.

The adjustment can be read on the scale (w).

2. Tighten the fence adjustment knob (l).

Rail Guide System

Guide rails, available in different lengths as

accessories, allow the use of the circular saw for

precise, straight clean cuts and simultaneously

protect the workpiece surface against damage.

In conjunction with additional accessories, exact

angled cuts, mitre cuts and fitting work can be

completed with the guide rail system.

Clamps (z) are available to secure the guide rail (x)

to the workpiece (fig. 6). Use of these clamps (z)

ensure that the guide rail (x) is securely attached to

the workpiece (y) for safe working. Once the guide

rail is set to the cut line and securely fixed to the

workpiece there is no movement during cutting.

IMPORTANT : The height scale on the unit is set for

using the saw without a guide rail. When using the

saw on the guide rail the difference in height will be

approximately 5.0 mm.

SETTING THE CIRCULAR SAW TO THE GUIDE RAIL

(FIG. 1, 7)

The clearance between the circular saw and the

guide rail (x) must be very small to achieve best

cutting results. The smaller this clearance the better

the straight line finish will be on the workpiece.

The clearance can be set with the two rail adjusters

(m, n) for each channel in the base for 0° cutting (m)

and for 1-45° bevel cutting (n). The rail adjusters

are precision cams that allow the reduction of

clearance between the unit and guide rail. Once

these adjusters have been set, sideways movement

of the saw during cutting is kept to a minimum while

allowing a smooth cutting action.

NOTE: The adjusters are set to minimum clearance

in the factory and may need adjusting and setting

before the unit is used. Use the following instructions

for setting the circular saw to the guide rail.

REMEMBER: Set all the rail adjusters on the saw to

the guide rail.

1. Undo the screw inside the rail adjuster to allow

for adjustment between the saw and the guide

rail.

2. Retract the lower guard and place the unit

on the guide rail, ensuring the blade is in the

highest position.

3. Rotate the adjuster until saw locks on guide rail.

IMPORTANT: Make sure the saw is securely

attached to the rail by trying to push the saw

forward. Ensure there is no movement of the

saw.

4. Rotate the adjuster back slightly until saw slides

easily along the rail.

5. Hold the rail adjuster in position and tighten the

screw again.

NOTE: ALWAYS adjust the system for use with

other rails.

The rail adjusters are now set up to minimise

sideways deviation when cutting with the saw on the

guide rail.

Before using the saw, the anti-splinter guard (aa) on

the guide rail will need tuning in. Refer to Tuning

the Anti-splinter Guard.

TUNING THE ANTI-SPLINTER GUARD

The guide rail (x) is equipped with an anti-splinter

guard (aa), which has to be tuned to the saw before

the first use.

The anti-splinter guard (aa) is situated on each edge

of the guide rail (fig. 7). The purpose of this anti-

splinter guard is to provide the user with a visible

blade cut line while reducing the chipping that

occurs along the workpiece cut edge during cutting.

IMPORTANT: ALWAYS read and follow the

Setting the Circular Saw to the Guide Rail

before cutting the splinter guard!

TUNING THE ANTI-SPLINTER GUARD (FIG. 8-11)

1. Place the guide rail (x) on a scrap piece of

wood (bb) with a minimum length of 100 mm

overhanging the workpiece. Use a clamp to

ensure that the guide rail is securely attached to

the workpiece. This will ensure accuracy.

2. Set the unit to a 15 mm depth of cut.

3. Place the front of the saw on the overhang end

of the guide rail, making sure that the blade is

positioned in front of the rail edge (fig. 9).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt d23551 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info