Bedienungsanleitung DeWalt D23700 T 2 (Seite 35 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546195

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

ENGLISH

6. Tighten the blade clamping screw firmly using

the wrench.

Adjusting the Riving Knife (ﬁ g. 5)

For the correct adjustment of the riving knife (g),

refer to the inset in figure 5. Adjust the clearance

of the riving knife after changing the saw blade or

whenever necessary.

1. Adjust the depth of cut to 0 mm to access both

clamping screws (u) of the riving knife.

2. Loosen the screws (u) and pull out the riving

knife to its maximum length.

3. Adjust the clearance and tighten the screw.

Adjusting the Cutting Line Marks

(ﬁ g. 6)

The marks for bevel cuts (l) and for straight cuts (m)

have two grooves each:

– narrow groove: for centring standard steel

blades

– wider groove: for centring TCT blades

To adjust, proceed as follows:

1. With the blade locked at 90°, make a trial cut

of approx. 400 mm.

2. Withdraw the saw slightly.

3. Slacken the screw (v) and align the cut (w) and

the mark (m).

4. Firmly tighten the screw (v).

Both cutting line marks are now correctly adjusted.

Mounting and Adjusting the Parallel

Fence (ﬁ g. 7)

The parallel fence (o) is used for cutting parallel to

the edge of the workpiece.

Mounting

1. Insert the parallel fence (o) in the saw shoe (f) as

shown.

2. Insert the bolt (x) into the hole (y).

3. Place the clamping bracket (z) over the bolt and

tighten the locking screw (aa).

Adjusting

1. Slacken the locking screw (aa) and set the

parallel fence (o) to the desired width. The

adjustment can be read on the scale (bb).

2. Tighten the locking screw (aa). The marks (cc)

and (dd) can be used as a guide: mark (cc): for

standard steel blades mark (dd): for TCT blades.

Prior to Operation

• Make sure the guards have been mounted

correctly. The saw blade guard must be in

closed position.

• Make sure the saw blade rotates in the direction

of the arrow on the blade.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING:

• Ensure the material to be sawn is

firmly secured in place.

• Apply only a gentle pressure to the

tool and do not exert side pressure on

the saw blade.

• Avoid overloading.

• Do not use excessively worn saw

blades. Do not use your saw for

pocket cuts.

Proper Hand Position (ﬁ g. 8)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Hold the tool by the main handle (ee) and the front

handle (c) to guide the saw properly.

Switching On and Off (ﬁ g. 1)

For safety reasons the on/off switch (a) of your tool is

equipped with a lock-off button (b). Press the lock-

off button to unlock the tool. To run the tool, press

the on/off switch (a). As soon as the on/off switch is

released the lock-off switch is automatically activated

to prevent unintended starting of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D23700 T 2 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info