546603

DeWalt D24000 T 2 Seite 40

40
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
38
ENGLISH
around the machine that allows handling of the workpiece without any
restrictions.
To reduce effects of vibration make sure the environment temperature is
not too cold, machine and accessory is well maintained and the workpiece
size is suitable for this machine.
WARNING:
• Always observe the safety instructions and applicable regulations.
• Check that the machine has been set up securely.
• Check that the workpiece is properly supported.
• Make sure the cutting disc is not contacting the workpiece
before the machine is switched on.
• Allow the motor to reach full speed before cutting.
• Apply only a gentle pressure to the machine. Do not force the
cutting action.
• Keep your hands out of the path of the cutting disc. Do not
place your hands within the marked area as shown in fi g. P.
Prior to operation:
• Install the appropriate cutting disc.
• Make sure all locking knobs and clamp handles are tight.
• Fill the water basin with the suffi cient amount of water for the water
pump to be fully submerged.
Switching on and off (fi g. Q)
• To switch the machine on, set the on/off switch (1) to position I.
• To switch the machine off, set the on/off switch (1) to position 0.
Wired into the mains cable is the residual current device (RCD) containing
the no-volt release switch and the motor overload protector with manual
reset. In case of a power shut-off, proceed as follows:
• Make sure the on/off switch (1) is in the off position.
• Press the reset button on the RCD.
Locking the switch
• In order to avoid unauthorised use of the machine, lock the switch
using a padlock.
Basic saw cuts
General handling
– Try a few simple projects using scrap material until you develop a “feel”
for the machine.
– Always make dry runs (without power) before fi nish cuts so that you
can check the path of the disc.
Vertical straight cross cut (fi g. R)
• Set the bevel angle to 0°.
• Lower the arm to bring the cutting disc in lowest position.
• Place the workpiece fl at on the table and against the fence, with the
fi nished side up. Align the marking on the workpiece with the marking
in the kerf indicator.
• Keep both hands away from the path of the cutting disc.
• Switch the machine on and allow the cutting disc to reach full speed.
Wait until the cutting disc is completely covered with water.
• Slowly feed the workpiece into the cutting disc, keeping it fi rmly
pressed against the fence. Do not force. The cutting disc speed should
be kept constant.
• After completing the cut, switch the machine off, allow the cutting disc
to stop and remove the workpiece.
Bevel cross-cut (fi g. S)
Bevel angles can be set at 22.5° and 45°.
• Loosen the bevel clamp knob (11) and set the bevel as desired.
• Tighten the bevel clamp knob fi rmly.
• Proceed as for a vertical straight cross-cut.
Diagonal cut (fi g. T1 & T2)
The edge guide (5) allows cutting of angles at 45°.
• Place the edge guide with the mounting bracket (72) over the fence.
• Flip the guide fence (73) into position for the required application:
– Flip the fence to the right for cutting small pieces from large tiles.
– Flip the fence to the left for any other application.
• Set the parallel fence to the required distance.
• Tighten the knob (74) to secure the guide in place.
• Proceed as for a vertical straight cross-cut.
Plunge cut (fi g. U)
A plunge cut is used to remove the centre of a tile, e.g. for electrical
outlets, drains, etc.
• Mark the area to be cut on both sides of the tile.
• Fit the appopriate size of cutting disc.
• Adjust the cutting depth to allow the cutting disc to saw only halfway
through the workpiece.
• Place the workpiece fl at on the table and against the fence, with the
fi nished side up. Align the marking on the workpiece with the marking
in the kerf indicator.
• Switch the machine on and allow the cutting disc to reach full speed.
Wait until the cutting disc is completely covered with water.
• Move the table until the marking on the workpiece is underneath the disc.
• Lower the arm to feed the cutting disc into the workpiece. Do not
overcut the mark. As soon as the marking has been cut, lock the arm
into its highest position.
• Repeat as for the other markings.
• Turn the workpiece upside down. Proceed as described above for the
second cuts to meet the fi rst.
• After completing the cut, switch the machine off, allow the cutting disc
to stop and remove the workpiece.
Grooving (fi g. V)
A groove is made into a tile e.g. to accommodate hidden wiring.
• Adjust the cutting depth as required.
• Place the workpiece fl at on the table and against the fence, with the
down side up. Align the marking on the workpiece with the marking in
the kerf indicator.
• Proceed as for a vertical straight cross-cut.
• Repeat the procedure to make a wider groove.
Optional accessories
WARNING: Since accessories, other than those offered by
D
EWALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the
risk of injury, only DEWALT recommended accessories should
be used with this product.
Range of cutting discs available
Type of disc Dimensions (diameter x bore) Usage
DT3733 250 x 25.4 mm Ceramic tile
DT3734 250 x 25.4 mm Porcelain/stone tile
Consult your dealer for further information on the appropriate accessories.
Transporting (fi g. W1 & W2)
The detachable parts can be stored in the water basin for easy transportation.
• Drain the water basin. See “Maintenance”.
• Remove the edge guide and the extension table.
• Lock the sliding table in position.
… 40 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt D24000 T 2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info