Bedienungsanleitung DeWalt D25500K T-1 (Seite 26 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544498

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Switching on and off (fig. A)

• To switch on the tool, press the on/off switch (1).

• To stop the tool, release the switch.

Drilling with a solid bit (fig. A)

• Insert the appropriate drill bit.

• Set the mode selector switch (4) to the “hammer

drilling” position.

• Set the electronic speed and impact control dial (2).

• Fit and adjust the side handle (8).

• If necessary, set the drilling depth.

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and switch on the

tool.

• Always switch off the tool when work is finished

and before unplugging.

Drilling with a core bit (fig. A)

• Insert the appropriate core bit.

• Assemble the centerdrill into the core bit.

• Set the mode selector switch (4) to the “hammer

drilling” position.

• Turn the electronic speed and impact control dial

(2) to a medium or high speed setting.

• Fit and adjust the side handle (8).

• Place the centerdrill on the spot and switch on

the tool. Drill until the core penetrates into the

concrete approx. 1 cm.

• Stop the tool and remove the centerdrill. Place the

core bit back into the hole and continue drilling.

When drilling through a structure thicker than the

depth of the core bit, break away the round

cylinder of concrete or core inside the bit at

regular intervals.

• To avoid unwanted breaking away of concrete

around the hole, first drill a hole the diameter of

the centerdrill completely through the structure.

Then drill the cored hole halfway from each side.

• Always switch off the tool when work is finished

and before unplugging.

Chipping and chiselling (fig. A)

• Insert the appropriate chisel and rotate it by hand

to lock it into one of 8 positions.

• Set the mode selector switch (4) to the

“hammering only” position.

• Set the electronic speed and impact control dial

(2).

• Fit and adjust the side handle (8).

• Switch on the tool and start working.

• Always switch off the tool when work is finished

and before unplugging.

Various types of SDS-max

drill bits and chisels are

available as an option.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Tool maintenance has to be carried out as soon as

the indicator LED lights up.

• This machine is not user-serviceable. Take the

tool to an authorised DEWALT repair agent after

approximately 80 hours of use. If problems occur

before this time contact an authorised DEWALT

repair agent.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Unwanted tools and the environment

Take your tool to an authorized DEWALT repair

agent where it will be disposed of in an

environmentally safe way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25500K T-1 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info