Bedienungsanleitung DeWalt D25500K T-1 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544498

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Hammering only: for light chipping,

chiselling and demolition applications.

In this mode the tool can also be used as

a lever to free a jammed drill bit.

• To select the operating mode, press the safety

lock (5) and rotate the mode selector switch (4)

until it is points to the symbol of the required mode.

• Release the safety lock and check that the mode

selector switch is locked in place.

Indexing the chisel position

The chisel can be indexed and locked into 8 different

positions (fig. D2).

• Rotate the mode selector switch (4) until it points

upward.

• Rotate the chisel in the desired position.

• Set the mode selector switch (4) to the

“hammering only” position.

• Twist the chisel until it locks in position.

Setting the electronic speed and impact control

dial (fig. B)

• Turn the dial (2) to the desired level. The higher

the number, the greater the speed and impact

energy. With dial settings from “1” (low) to “5”

(full power) the tool is extremely versatile and

adaptable for many different applications.

The required setting is a matter of experience.

E.g.:

- when chiselling or drilling in soft, brittle

materials or when minimum break-out is

required, set the dial to “1” or “2” (low);

- when breaking or drilling in harder materials,

set the dial to “5” (full power).

D25600

With dial settings from “1” to “7” the tool allows a

further fine-adjustment to the choice of application.

Assembling and fitting the side handle (fig. E1 - E4)

The side handle (8) can be mounted in front or in

rear position on either side of the machine to suit

both RH- and LH-users.

Always operate the tool with the side

handle properly assembled.

Mounting in front position (fig. E1 & E2)

• Snap the steel ring (16) over the collar (7) behind

the tool holder (6). Squeeze both ends together,

mount the bush (14) and insert the pin (15).

• Place the side handle clamp (13) and screw on

the clamp wheel (9). Do not tighten.

• Screw the side handle (8) into the clamp wheel

and tighten it.

• Rotate the side handle mounting assembly to the

desired position. For drilling horizontally with a

heavy drill bit, we recommend to place the side

handle at an angle of approx. 20° for optimum

control (fig. E2).

• Lock the side handle mounting assembly in place

by tightening the clamp wheel (9).

Mounting in rear position (fig. E3 & E4)

The rear position is particularly useful when drilling

overhead or down into a floor. Refer to fig. D4.

• Unscrew the side handle (8) and remove it from

the front position. Leave the side handle

mounting assembly in front position so that the

depth adjustment rod can still be used.

• Screw the side handle directly into one of the

rear side handle positions (10) on either side of

the tool.

Setting the drilling depth (fig. F)

• Insert the required drill bit.

• Loosen the clamp nut (17) and fit the depth

adjustment rod (11) through the hole in the side

handle clamp.

• Push the drill bit into a surface at a right angle and

adjust the depth adjustment rod (11) as shown.

• Tighten the clamp nut (17).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• For your own safety, always use the tool

with both hands.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool

(approx. 20 kg). Excessive force does

not speed up drilling or chiselling but

decreases tool performance and may

shorten tool life.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25500K T-1 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info