Bedienungsanleitung DeWalt D27105 T 3 (Seite 24 von 26) (Englisch)

546215

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

ENGLISH

• After completing the cut, switch the machine off, allow the saw blade

to stop and remove the workpiece.

WARNING: Never push or hold the free or cut-off side of the

workpiece.

WARNING: Always use a push stick when ripping small

workpieces.

Bevel cuts (ﬁ g. U2)

• Set the required bevel angle.

• Proceed as for ripping.

Cross-cutting (ﬁ g. V1)

• Set the bevel angle to 0°.

• Adjust the saw blade height.

• Set the mitre fence to 0°.

• Proceed as for ripping, only use the mitre fence to push the workpiece

through the blade.

Bevel cross-cutting

• Set the required bevel angle.

• Proceed as for cross-cutting.

Mitre cuts ( g. V2)

• Set the mitre fence to the required angle.

• Proceed as for cross-cutting.

Optional attachments

WARNING: Prior to assembling any accessories always unplug

the machine.

Dust extraction kit (ﬁ g. W1 & W2)

WARNING! This machine is provided with two dust extraction

points for use in each mode.

WARNING! Whenever possible, connect a dust extraction

device designed in accordance with the relevant regulations

regarding dust emission.

WARNING! When sawing wood, connect a dust extraction

device designed in accordance with the relevant regulations

regarding dust emission.

Connect a dust collection device designed in accordance with the relevant

regulations. The air velocity of externally connected systems shall be 20

m/s ±2 m/s. Velocity to be measured in the connection tube at the point of

connection, with the tool connected but not running.tion tube at the point of

connection, with the tool connected but not running.

Connecting - mitre saw position (ﬁ g. W1)

• Connect the one end of the ﬁ rst hose to the dust extraction adaptor (13).

• Insert the other end of the hose into the middle inlet port of the

manifold (128).

• Connect the one end of the other hose to the under-table guard (63).

• Insert the other end of the hose into the outer inlet port of the manifold.

Connecting - saw bench position (ﬁ g. W2)

• Proceed as for mitre saw position, only connect the hose from the

under-table guard to the saw blade guard (21).

Mitre saw extra support/length stop (ﬁ g. A5)

The extra support and length stop can be mounted on the left-hand side

or on the right-hand side, or with two sets on either side.

• Fit the items 31 - 39 onto the two guide rails (32 & 33).

• Use the inclinable support (34) for cross-cutting 210 mm wide boards

(15 mm thick).

Roller support table (ﬁ g. A6)

The roller support table (40) is used to support long workpieces. In mitre

saw mode, the roller support table can be mounted on the left-hand side

or on the right-hand side, or with two sets on either side. In saw bench

mode, it can also be mounted in front or at the rear of the saw table.

Side extension table (ﬁ g. A8)

The side extension table increases the distance from the rip fence to

the blade to 600 mm or more, depending on the rod length ﬁ tted to the

machine and the clamped position of the table. The side extension table

must be used in conjunction with guide rails (32) (option). The adjustable

table is equipped with an engraved scale along its front edge and

mounted on a sturdy base which clamps to the guide rods.

• Fit the extension table to the right-hand side of the machine for

continuity of the distance scale on both tables.

Sliding table (ﬁ g. A9)

This sliding table (43) allows for board sizes to the left of the blade up to

1200 x 900 mm.

The guide rods are mounted on a sturdy alloy extrusion which is quickly

detachable from the machine and yet fully adjustable is all planes.

The fence incorporates a full length measuring tape for quick positioning

of an adjustable stop and an adjustable support for narrow workpieces.

Transporting (ﬁ g. X)

WARNING: Always transport the machine in saw bench mode

with the upper blade guard fitted.

The castor wheels provide an easier transport of the machine.

• Put the machine on the right base side.

• Fold the rear legs into the base

• Fold the front legs out of the base

• Turn the machine straight up.

• Lift the machine by the front legs up to the wheels are in contact with

the floor.

WARNING: When carrying the machine, always seek

assistance.

Maintenance

Your DEWALT power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing

and removing accessories, before adjusting or changing

set-ups or when making repairs. Be sure the trigger switch

is in the OFF position. An accidental start-up can cause injury.

Lubrication

The bearings of the motor are pre-lubricated and watertight.

• Slightly oil the rotating table bearing surface where it slides on the lip of

the ﬁ xed table at regular intervals.

• Periodically lubricate the depth of cut screwthread.

• Clean the parts subject to accumulation of sawdust and chips

periodically with a dry brush.

Cam adjustment (ﬁ g. Y1 - Y3)

To take out the clearance between the two tables, proceed as follows:

• Rotate the machine into saw bench mode.

• Remove the screws (138) and the retainer plate (139).

DeWalt D27105 T 3 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info