Bedienungsanleitung DeWalt D27107 T 3 (Seite 41 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546219

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

Safety Instructions

WARNING! When using electric tools basic safety precautions

should always be followed to reduce the risk of fire, electric

shock and personal injury including the following.

Read all these instructions before attempting to operate this product and

save these instructions.

SAVE THIS MANUAL FOR FUTURE REFERENCE

General Safety Rules

1. Keep work area clear.

Cluttered areas and benches invite injuries.

2. Consider work area environment.

Do not expose the tool to rain. Do not use the tool in damp or wet

conditions. Keep the work area well lit (250 - 300 Lux). Do not use

the tool where there is a risk of causing fire or explosion, e.g., in the

presence of flammable liquids and gases.

3. Guard against electric shock.

Avoid body contact with earthed surfaces (e.g., pipes, radiators,

cookers and refrigerators). When using the tool under extreme

conditions (e.g., high humidity, when metal swarf is being produced,

etc.), electric safety can be improved by inserting an isolating

transformer or a (FI) earth-leakage circuit-breaker.

4. Keep other persons away.

Do not let persons, especially children, not involved in the work, touch

the tool or the extension cord and keep them away from the work area.

5. Store idle tools.

When not in use, tools must be stored in a dry place and locked up

securely, out of reach of children.

6. Do not force the tool.

It will do the job better and safer at the rate to which it was intended.

7. Use the right tool.

Do not force small tools to do the job of a heavy duty tool. Do not use

tools for purposes not intended; for example do not use circular saws

to cut tree limbs or logs.

8. Dress properly.

Do not wear loose clothing or jewellery, as these can be caught in

moving parts. Non-skid footwear is recommended when working

outdoors. Wear protective hair covering to contain long hair.

9. Use protective equipment.

Always use safety glasses. Use a face or dust mask if working

operations create dust or flying particles. If these particles might be

considerably hot, also wear a heat-resistant apron. Wear ear protection

at all times. Wear a safety helmet at all times.

10. Connect dust extraction equipment.

If devices are provided for the connection of dust extraction and

collecting equipment, ensure these are connected and properly used.

11. Do not abuse the cord.

Never yank the cord to disconnect it from the socket. Keep the

cord away from heat, oil and sharp edges. Never carry the tool by its

cord.

12. Secure work.

Where possible use clamps or a vice to hold the work. It is safer than

using your hand and it frees both hands to operate the tool.

13. Do not overreach.

Keep proper footing and balance at all times.

14. Maintain tools with care.

Keep cutting tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories. Inspect

tools periodically and if damaged have them repaired by an authorized

service facility. Keep handles and switches dry, clean and free from oil

and grease.

15. Disconnect tools.

When not in use, before servicing and when changing accessories such

as blades, bits and cutters, disconnect tools from the power supply.

16. Remove adjusting keys and wrenches.

Form the habit of checking to see that adjusting keys and wrenches are

removed from the tool before operating the tool.

17. Avoid unintentional starting.

Do not carry the tool with a finger on the switch. Be sure that the tool is

in the “off” position before plugging in.

18. Use outdoor extension leads.

Before use, inspect the extension cable and replace if damaged.

When the tool is used outdoors, use only extension cords intended for

outdoor use and marked accordingly.

19. Stay alert.

Watch what you are doing. Use common sense. Do not operate the tool

when you are tired or under the influence of drugs or alcohol.

20. Check for damaged parts.

Before use, carefully check the tool and mains cable to determine

that it will operate properly and perform its intended function. Check

for alignment of moving parts, binding of moving parts, breakage of

parts, mounting and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or

replaced by an authorized service centre unless otherwise indicated

in this instruction manual. Have defective switches replaced by an

authorized service centre.

Do not use the tool if the switch does not turn it on and off.

Never attempt any repairs yourself.

WARNING! The use of any accessory or attachment or

performance of any operation with this tool other than those

recommended in this instruction manual may present a risk of

personal injury.

21. Have your tool repaired by a qualified person.

This electric tool complies relevant safety rules. Repairs should only be

carried out by qualified persons using original spare parts; otherwise this

may result in considerable danger to the user.

Additional safety rules for mitre saws

• Make sure all locking knobs and clamp handles are tight before starting

any operation.

• Ensure that the machine arm is securely fixed when performing bevel

cuts.

• Do not operate the machine without the guard in position, or if the

guard does not function or is not maintained properly.

• Never place either hand in the blade area when the saw is connected to

the electrical power source.

• Never attempt to stop a machine in motion rapidly by jamming a tool or

other means against the blade; serious accidents can occur.

• Select the correct blade for the material to be cut.

• Never perform any cleaning or maintenance work when the machine is

still running and the head is not in the rest position.

• The front section of the guard is louvred for visibility while cutting.

Although the louvres dramatically reduce flying debris, there are

openings in the guard and safety glasses should be worn at all times

when viewing through the louvres.

• With laser assembled do not exchange with other types of laser.

Repairs shall only be performed by the laser manufacturer or an

authorized agent.

• Never cut workpiece shorter than 200mm.

• Without additional support the machine is designed to accept the

maximum workpiece size of:

– Height 63 mm by width 205 mm by length 500 mm

– Longer workpieces need to be supported by suitable additional

table, e.g. DE3474. Always clamp the workpiece safely.

• During use in mitre saw mode ensure that the portion of the saw blade,

below the table, is completely enclosed by the guard (63) shown in

Fig.E.

Additional safety rules for saw benches

• Make sure that the blade rotates in the correct direction and the teeth

are pointing to the front of the saw bench.

DeWalt D27107 T 3 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info