Bedienungsanleitung DeWalt D27107 T 3 (Seite 44 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546219

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

42 Extension table (D271058)

43 Sliding table (D271055)

Push sticks (DE3454) (not shown)

For use in all modes:

A10

44 Three way dust extraction kit (D271054)

A11

144 LED Worklight System

INTENDED USE

Your D

EWALT D27107 flip-over saw has been designed to operate as a

mitre saw or a saw bench to perform the four main sawing operations of

ripping, cross-cutting, bevelling and mitring easily, accurately and safely.

This unit is designed for use with a nominal blade diameter 305 mm carbide

tip blade for professional cutting wood, wood products and plastics.

DO NOT use under wet conditions or in presence of flammable liquids or

gases.

These flip over saws are professional power tools.

DO NOT let children come into contact with the tool. Supervision is required

when inexperienced operators use this tool.

WARNING! Do not use the machine for purposes other than

intended.

• This product is not intended for use by persons (including children)

suffering from diminished physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are supervised by a person

responsible for their safety. Children should never be left alone with this

product.

MITRE SAW MODE

In mitre saw mode, the sawing machine is used in vertical, mitre or bevel

position.

BENCH SAW MODE

Turned over on its central axis, the sawing machine is used to perform

the standard ripping operation and for sawing wide pieces by manually

feeding the workpiece into the blade.

Electrical Safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

Your tool is double insulated in accordance with EN 61029;

therefore no earth wire is required.

In case of cord replacement the tool must only be repaired by an authorized

service agent or by qualified electrician.

Mains Plug Replacement

(U.K. & Ireland only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved 3–core extension cable

suitable for the power input of this tool (see Technical Data).The minimum

conductor size is 1.5 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable completely.

ASSEMBLY

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing

and removing accessories, before adjusting or changing

set-ups or when making repairs. Be sure the trigger switch

is in the OFF position. An accidental start-up can cause injury.

Unpacking the machine and its parts

WARNING: To reduce the risk of injury, always seek assistance

when moving the machine.

• Remove the loose packaging material from the box.

• Lift the machine out of the box.

• Remove the parts box from the interior of the machine.

• Remove any remaining packing material from the machine.

Mounting the feet (ﬁ g. A2, B, B1)

With the feet and legs mounted, alternatively the machine is suitable for

placement on a workbench. To ensure a safe operation, the machine must

be fastened to the workbench.

WARNING! Never operate this machine when it is not fastened

to the workbench. The feed force will make the saw unstable if

not fastened to the workbench.

• Turn the machine upside down.

• Place a foot (16) on each of the mounting locations (51) on the base.

• Slide a nut (52) into the slots (53) located above the mounting locations.

• Insert a bolt (54) fitted with a washer (55) into the feet.

• Tighten the bolts.

• Mount the legs as described below.

• Fold the legs as described below .

• Turn the machine straight up.

• Insert a bolt of 8mm and 120mm minimum length (49) into the feet on

each mounting location (fig. B1).

• Tighten the bolts.

Mounting the legs (ﬁ g. C1 & C2)

With the legs mounted, the machine is suitable for stand-alone placement.

• Turn the machine upside down.

• Mount the legs as described below. Beware that the front legs and the

rear legs have different lengths. The rear legs are slightly longer than

the front legs. Make sure to mount the legs in the correct place.

• Turn the machine straight up. Make sure it is level; adjust the leg

clamping height if required.

Rear legs

• Present a leg (15) to each of the mounting points (56) located at the

lower edges on the inside of the base (ﬁ g. C1).

• Pass a coach bolt (57) from the outside through the holes into the

frame and the legs.

• Place a bracket (58) and a lock knob (59) onto the bolts.

• Tighten the lock knobs.

Front legs

• Present a leg (15) to each of the mounting points (56) located at the

upper edges on the inside of the base (ﬁ g. C2).

• Place a bracket (58) over the legs.

• Pass a coach bolt (57) from the inside through the holes into the

brackets, the legs and frame.

• Place a lock knob (59) onto the bolts.

• Tighten the lock knobs.

Folding the legs (ﬁ g. C3, C4)

The legs can be folded into the base to make the machine suitable for use

on a workbench.

• Turn the machine upside down.

DeWalt D27107 T 3 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info