Bedienungsanleitung DeWalt D51430 (Seite 20 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546470

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

• Do not use any stands for mounting the tool to

a support.

• Do not disassemble or block any parts of the

fastener driving tool such as the safety yoke.

• Prior to each operation check that the safety and

triggering mechanism is functioning properly and

that all nuts and bolts are tight.

• Do not use the equipment as a hammer.

• Never point any operational fastener driving tool

at yourself or at any other person. Do not use the

tool in applications requiring operation close to

the body.

• While working, hold the tool in such a way that

no injuries can be caused to the head or to the

body in the event of a possible recoil due to

a disruption in the energy supply or hard areas

within the workpiece.

• Never actuate the fastener driving tool into free

space.

• Consider the conditions in the work area.

Fasteners can penetrate thin workpieces or slip

off corners and edges of the workpiece, and thus

put people at risk.

• Do not drive fasteners close to the edge of the

workpiece.

• Do not drive fasteners on top of other fasteners.

• In the work area, carry the tool at the workplace

using only one handle, and never with the trigger

actuated.

• Unload the tool after use and before performing

any maintenance.

The following pictograms are shown on the tool:

Pneumatic tool with safety yoke.

Do not use the tool on a ladder.

Compatible fastener angles.

Maximum number of fasteners in

magazine.

Fastener width.

Fastener length.

Max. operating pressure.

Tool weight.

Package contents

The package contains:

1 Stapler

1 Sequential action trigger

1 Safety glasses

1 Allen key 3 mm

1 Allen key 4 mm

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories

which may have occurred during transport.

• Take the time to thoroughly read and understand

this manual prior to operation.

Description (fig. A)

Your stapler D51430/D51431 has been designed for

driving fasteners into wooden workpieces.

1 Trigger

2 Lock-off switch

3 Depth adjustment slider

4 Contact trip

5 Magazine

6 Magazine latch

7 Air fitting

Assembly and adjustment

Trigger selection (fig. B)

These tools are assembled with a bump action

trigger. A sequential action trigger is also included

with the original packaging. For definitions of

„bump action“ and „sequential action“, see below.

- The grey trigger with a single fastener printed on

the side is the sequential action trigger.

Installation of this kit causes the tool to function

in sequential action mode.

- The black trigger with three fasteners printed on the

side is the bump action trigger. Installation of this kit

causes the tool to function in bump action mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D51430 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info