Bedienungsanleitung DeWalt D51430 (Seite 22 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546470

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

• Increase the air pressure to the normal operating

level.

• Use the tool in the normal manner.

Hot weather operation

The tool should operate normally. Avoid the heat of

direct sunlight to avoid damage to the bumpers,

o-rings, and other rubber parts.

Actuating the tool (fig. A)

The tool can be operated using one of two modes.

The trigger installed on the tool determines the

mode of actuation.

Sequential action mode

The sequential action mode is used for intermittent

fastening when very careful and accurate placement

is desired.

• Fit the grey trigger as described above.

• Release the trigger lock (2).

• Push the contact trip (4) against the work surface.

• Pull the trigger (1) to actuate the tool.

Each trigger pull with the contact trip pushed

against the work surface will drive one fastener.

Bump action mode

The bump action mode is used for rapid fastening

on flat, stationary surfaces.

• Fit the black trigger as described above.

• Release the trigger lock (2).

• To drive a single fastener: Operate the tool as

described for sequential action.

• To drive several fasteners: Pull the trigger (1) first,

and then push the contact trip (4) repeatedly

against the work surface.

Do not keep the trigger depressed when

the tool is not in use. Keep the trigger

lock engaged to prevent accidental

actuation when the tool is not in use.

Clearing a jammed fastener (fig. E)

If a fastener becomes jammed in the nosepiece,

follow these instructions to remove the fastener:

• Disconnect the airline from the tool.

• Engage the trigger lock (2).

• Remove all fasteners from the magazine.

• Flip up the front latch (13) and move the bracket (14)

out of the way so that barrel (15) can be opened.

• Remove the bent fastener, using pliers if necessary.

• If the driving blade is in the down position, push

the driving blade upward using a screwdriver.

• Close the barrel (15) and put the bracket (14)

back in position.

• Press the front latch (13) into the locked position.

• Feed the fasteners into the nose piece as

described under „Loading the tool“.

If fasteners become jammed in the

nosepiece frequently, have the tool

serviced by an authorised DEWALT

service centre.

Optional accessories

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT tool has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends on proper tool care and regular cleaning.

The following maintenance operations must be

performed every day.

Cleaning

• Clean the magazine and the nosepiece using

compressed air.

• Clean the front end of the contact trip using fuel

oil or diesel fuel.

Draining

• Drain all condensation from the air compressor

tanks and hoses.

Lubrication

• Insert 5 - 7 drops pneumatic tool oil into the air

fitting on the end cap of the tool.

Checking

• Ensure that all fasteners on the tool are tight and

undamaged.

• Tighten loose fasteners using the appropriate tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D51430 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info