Bedienungsanleitung DeWalt D51850 (Seite 31 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546481

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

ENGLISH

INTENDED USE

The D51825 and D51850 pneumatic nailers have

been designed for driving fasteners into wooden

workpieces.

DO NOT use under humid conditions or in presence

of flammable liquids or gases.

These pneumatic nailers are professional power

tools. DO NOT let children come into contact with

the tool. Supervision is required when inexperienced

operators use this tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, ALWAYS lock-off trigger,

disconnect air line from tool and remove

fasteners from the magazine before

making and adjustments or personal

injury may result.

Trigger

WARNING: Keep fingers AWAY from

trigger when not driving fasteners to

avoid accidental firing. Never carry tool

with finger on trigger. In Contact Bump

Actuation Mode tool will fire a fastener

if safety is bumped while trigger is

depressed.

These tools are assembled with a bump action

trigger. A sequential action trigger is also included

with the original packaging. For definitions of “bump

action” and “sequential action”, see below.

The gray trigger with imprinted on the side is

the single sequential action trigger and causes the

tool to operate in this mode.

The black trigger with imprinted on the side is

the bump action trigger and permits the tool to be

actuated in this manner.

For defining the use of the sequential action trigger

and bump action trigger, see Actuating the Tool.

TRIGGER REMOVAL (FIG. 2)

1. Remove rubber grommet (i) from the end of the

dowel pin (j).

2. Remove dowel pin.

3. Remove trigger assembly from trigger cavity

under the handle of the tool housing.

TRIGGER INSTALLATION (FIG. 3)

1. Select either the sequential or bump action

trigger to be installed on the tool.

2. Insert the trigger assembly into trigger cavity

making sure that the trigger spring (k) is placed

around trigger valve stem (l).

3. Ensure that the contact trip (d) is pushed fully

upward so that it is flush with the tool housing

and aligned with the housing holes.

4. Insert the dowel pin (j) through the tool frame

and trigger assembly as shown.

5. Push the rubber grommet (i) onto the end of the

dowel rod.

Air Fitting (ﬁ g. 1)

These tools have a standard 3/8" pipe thread for

the air fitting (g). The tool is assembled with a 3/8"

to 1/4" adapter installed in the end cap.

• Wrap the male end of the fitting with Teflon tape

to prevent air leaks.

• To install a 1/4" fitting, screw the fitting into the

3/8" to 1/4" adapter in the end cap and tighten

firmly.

• To install a 3/8" fitting, remove the 3/8" to 1/4"

adapter, if present. Screw the fitting into the end

cap and tighten firmly.

OPERATION

Instructions for Use

WARNING: ALWAYS observe the

safety instructions and applicable

regulations.

WARNING: ALWAYS place workpiece

safely.

Proper Hand Position (ﬁ g. 9)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main

handle (m).

Preparing the Tool (ﬁ g. 1)

WARNING: To reduce the risk of

personal injury, disconnect tool from air

supply before performing maintenance,

clearing a jammed fastener, leaving work

area, moving tool to another location or

handing the tool to another person.

WARNING: Wear proper eye, hearing

and respiratory protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D51850 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info