Bedienungsanleitung DeWalt dc 300 kl qw (Seite 38 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

382886

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

ENGLISH

Lower Guard Safety Instructions

a Check lower guard for proper closing

before each use. Do not operate the saw if

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position.

If saw is accidentally dropped, lower guard

may be bent. Raise the lower guard with the

retracting handle and make sure it moves freely

and does not touch the blade or any other part,

in all angles and depths of cut.

b Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use.

Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up

of debris.

c Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts”. Raise lower guard

by retracting handle and as soon as blade

enters the material, the lower guard must be

released.

For all other sawing, the lower guard should

operate automatically.

d Always observe that the lower guard is

covering the blade before placing saw down

on bench or ﬂ oor.

An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in

its path. Be aware of the time it takes for the

blade to stop after switch is released.

Additional safety instructions for circular saws

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Preferably wear a dust mask.

• Do not use blades of larger or smaller diameter

than recommended. For the proper blade

rating refer to the technical data. Use only the

blades speci ed in this manual, complying with

EN 847-1.

• Never use abrasive cut-off wheels.

Additional Safety Instructions for All

Saws with Riving Knife

a) Use the appropriate riving knife for the blade

being used. For the riving knife to work, it must

be thicker than the body of the blade but thinner

than the tooth set of the blade.

b) Adjust the riving knife as described in

this instruction manual. Incorrect spacing,

positioning and alignment can make the riving

knife ineffective in preventing kickback.

c) For the riving knife to work, it must be

engaged in the work piece. The riving knife is

ineffective in preventing kickback during short

cuts.

d) Do not operate the saw if riving knife is bent.

Even a light interference can slow the closing rate

of a guard.

Residual Risks

The following risks are inherent to the use of circular

saws.

– Injuries caused by touching the rotating parts or

hot part of the tool.

In spite of the application of the relevant safety

regulations and the implementation of safety devices,

certain residual risks cannot be avoided. These are:

– Impairment of hearing .

– Risk of squeezing fingers when changing the

accessory.

– Health hazards caused by breathing dust

developed when working in wood.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dc 300 kl qw Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info