79272

DeWalt DC 411 Seite 48

48
Zoom out
Zoom in
Vorherige Seite
1/220
Nächste Seite
ENGLISH
46
CAUTION: Guards must be used
with all grinding wheels, cutting
wheels, wire brushes and wire
wheels. The DC411 is provided with a
guard intended for use with depressed
center wheels (Type 27) and hubbed
grinding wheels (Type 27). The same
guard is designed for use with and wire
cup brushes.
1. Open the guard latch (p), and align the lugs (m)
on the guard with the slots (n) on the gear case.
2. Push the guard down until the guard lugs
engage and rotate freely in the groove on the
gear case hub.
3. With the guard latch open, rotate the guard (i)
into the desired working position. The guard
body should be positioned between the spindle
and the operator to provide maximum operator
protection.
4. Close the guard latch to secure the guard on
the gear case. You should not be able to rotate
the guard by hand when the latch is closed. Do
not operate the grinder with a loose guard or
the clamp lever in open position.
5. To remove the guard, open the guard latch,
rotate the guard so that the lugs are aligned
with the slots and pull up on the guard.
NOTE: The guard is pre-adjusted to the diameter of
the gear case hub at the factory. If, after a period of
time, the guard becomes loose, tighten the adjusting
screw (o) with clamp lever in the closed position with
guard installed on the tool.
CAUTION: Do not tighten the adjusting
screw with the clamp lever in the open
position. Undetectable damage to the
guard or the mounting hub may result.
CAUTION: If the guard cannot be
tightened by the adjusting clamp, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
CAUTION: To reduce the risk of
damage to the tool, do not tighten the
adjusting screw with the clamp lever
in the open position. Undetectable
damage to the guard or the mounting
hub may result.
NOTE: Edge grinding and cutting can be performed
with Type 27 wheels designed and specified for this
purpose; 6.35 mm (1/4") thick wheels are designed
for surface grinding while 3.17 mm (1/8") wheels are
designed for edge grinding.
OPERATION
Switch
LOCK-OFF BUTTON AND TRIGGER SWITCH (FIG. 6)
Your cut-off tool is equipped with a lock-off button (b).
To lock the trigger switch, press the lock-off button
as shown. When the lock-off button is depressed to
the lock icon, the unit is locked.
Always lock the trigger switch when carrying or
storing the tool to eliminate unintentional starting.
To unlock the trigger switch, press the lock-off
button. When the lock-off button is depressed to the
unlock icon, the unit is unlocked. The lock-off button
is colored red to indicate when the switch is in its
unlocked position.
Pull the trigger switch (a) to turn the tool ON.
Releasing the trigger switch turns the tool OFF.
NOTE: This tool has no provision to lock the switch in
the ON position, and should never be locked ON by
any other means.
CAUTION: Hold the side handle and
body of the tool firmly to maintain
control of the tool at start up and during
use and until the wheel or accessory
stops rotating. Make sure the wheel has
come to a complete stop be fore laying
the tool down.
CAUTION: Allow the tool to reach full
speed before touching tool to the work
surface. Lift the tool from the work
surface before turning the tool off.
SPINDLE LOCK
The spindle lock pin is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock pin only when the
tool is turned off, the battery is removed, and the
wheel has come to a complete stop.
CAUTION: To reduce the risk of
damage to the tool, do not engage the
spindle lock while the tool is operating.
Damage to the tool will result and
attached accessory may spin off
possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
… 48 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DC 411 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info