Bedienungsanleitung DeWalt DC318KL (Seite 41 von 176) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546383

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

ENGLISH

Pos. Wood Metal Plastics

3 Fast cuts - PVC

2 Thick workpieces - Fibreglass

Acrylic

1 Plywood Aluminium -

Chipboard Non-ferrous -

0 Thin workpieces Sheet metal -

Fine cuts

Setting the sawdust blower (ﬁ g. A)

The sawdust blower conducts an adjustable

stream of air to the saw blade to keep the

workpiece clear of sawdust during operation.

• Set the sawdust blower using the lever (3).

- Low For working with metals, when

using coolants and lubricants

and for use with dust extraction.

- Intermediate For working with wood and

similar materials in low speed.

- High For working with wood and

similar materials in high speed.

Mounting the plastic anti-scratch shoe cover

(ﬁ g. E)

The anti-scratch shoe cover (16) reduces damage

to the surface of (sensitive) workpieces.

• Click the cover onto the shoe as shown.

Mounting and removing the anti-splinter shoe

insert (ﬁ g. F1 & F2)

The anti-splinter shoe insert (17) which ﬁ ts close to

the saw blade reduces splintering of the workpiece.

The insert can be mounted both into the shoe and

the shoe cover.

• Hold the insert (17) in the orientation as shown.

• To mount the insert into the shoe (8):

– Slide the edges (18) into the grooves (19).

– Slide the insert back into position against the

shoe.

• To mount the insert into the cover (16):

– Slide the edges (18) behind the ribs (20).

– Push the front end of the insert towards the

cover. The insert snaps into place.

• To remove the anti-splinter shoe insert do the

above process in reverse order.

Dust extraction (ﬁ g. G)

The dust extraction adaptor (21) in combination with

the dust extraction shroud (22) helps extracting the

dust from the workpiece surface, when connected

to a suitable dust extraction system.

• Place the dust extraction shroud (22) onto the

ﬁ nger guard (5) until it clicks in place.

• Fit the dust extraction adaptor (21) to the tool

as shown.

• Connect the hose of a suitable dust extraction

system to the adaptor.

WARNING: Inhalation of dust

developed when sawing wood presents

a serious health hazard. Always

connect a dust extraction system

designed in compliance with the

applicable directives regarding dust

emission.

Preferably wear a dust mask.

WARNING: Do not use a dust extraction

system without proper spark protection

when sawing metal.

Prior to operation

• Make sure your battery pack is (fully) charged.

• Make sure the battery pack is properly seated.

OPERATION

Instructions for use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Make sure your workpiece is well secured.

Remove nails, screws and other

fasteners that may damage the blade.

• Check that there is sufﬁ cient space for

the blade underneath the workpiece.

Do not cut materials that are thicker

than the maximum cutting depth.

• Use sharp saw blades only. Damaged

or bent saw blades must be removed

immediately.

• Do not use the tool for sawing pipes or

tubes.

• Never run your tool without a saw blade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC318KL Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info