Bedienungsanleitung DeWalt DC318KL (Seite 42 von 176) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546383

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

ENGLISH

• For optimal results, move the tool

smoothly and constantly over the

workpiece. Do not exert lateral pressure

on the saw blade. Keep the shoe ﬂ at on

the workpiece. When sawing curves,

circles or other round shapes, push the

tool gently forward.

• Wait until the tool has come to a

standstill before removing the saw blade

from the workpiece. After sawing the

blade may be very hot. Do not touch.

Proper Hand Position (ﬁ g. A, L)

WARNING: To reduce the risk of serious

personal injury, ALWAYS use proper

hand position as shown.

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in

anticipation of a sudden reaction.

Proper hand position requires one hand on the top

handle (15), with the other hand on the main handle

(23).

Switching on and off (ﬁ g. H)

For safety reasons your tool is equipped with a

safety lock.

• To unlock the tool, release the safety lock (2).

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in off position, activate the

safety lock.

WARNING: After using the tool for an

extended period on low speed settings,

run it for approx. 3 minutes on maximum

no-load speed.

Sawing in wood

• If necessary, draw a cutting line.

• Switch the tool on.

• Hold the tool against the workpiece and follow

the line.

• For sawing parallel to the edge of your workpiece,

install the parallel fence and guide your jigsaw

along the workpiece a shown in ﬁ gure I.

Sawing in wood using a pilot hole

• If necessary, draw a cutting line.

• Drill a hole (ø min. 12 mm) and introduce the

saw blade.

• Switch the tool on.

• Follow the line.

• For cutting perfectly round shapes, install the

trammel bar and set it to the required radius

(ﬁ g. J).

Sawing up to a projecting edge (ﬁ g. K)

• Using a conventional blade, cut up to the

projected edge.

• Finish off the cut using a ﬂ ush cutting blade.

Dust extraction (ﬁ g. G)

• When the tool is used indoor for extended

periods of time, use a suitable dust extractor

designed in compliance with the applicable

Directives regarding dust emission.

Sawing in metal

• Mount an appropriate saw blade.

• Proceed as described above.

CAUTION: Use a cooling lubricant

(cutting oil) to prevent overheating of

the saw blade or the workpiece.

Optional accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

These include:

– DE3241 Parallel guide

– DE3242 Trammel bar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC318KL Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info