Bedienungsanleitung DeWalt dc411n xj 18v 4 1 2 angle grinder bare (Seite 55 von 264) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

391260

Zoom out

Zoom in

Vorherige Seite

1/264

Nächste Seite

ENGLISH

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Proper Hand Position (ﬁ g. 1, 9)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (e), with the other hand on the main

handle (q).

Switch

LOCK-OFF BUTTON AND TRIGGER SWITCH (FIG. 6)

Your cut-off tool is equipped with a lock-off button (b).

To lock the trigger switch, press the lock-off button

as shown. When the lock-off button is depressed to

the lock icon, the unit is locked.

Always lock the trigger switch when carrying or

storing the tool to eliminate unintentional starting.

To unlock the trigger switch, press the lock-off

button. When the lock-off button is depressed to the

unlock icon, the unit is unlocked. The lock-off button

is colored red to indicate when the switch is in its

unlocked position.

Pull the trigger switch (a) to turn the tool ON.

Releasing the trigger switch turns the tool OFF.

NOTE: This tool has no provision to lock the switch in

the ON position, and should never be locked ON by

any other means.

CAUTION: Hold the side handle and

body of the tool firmly to maintain

control of the tool at start up and during

use and until the wheel or accessory

stops rotating. Make sure the wheel has

come to a complete stop be fore laying

the tool down.

CAUTION: Allow the tool to reach full

speed before touching tool to the work

surface. Lift the tool from the work

surface before turning the tool off.

SPINDLE LOCK

The spindle lock pin is provided to prevent the

spindle from rotating when installing or removing

wheels. Operate the spindle lock pin only when the

tool is turned off, the battery is removed, and the

wheel has come to a complete stop.

NOTICE: To reduce the risk of damage

to the tool, do not engage the spindle

lock while the tool is operating. Damage

to the tool will result and attached

accessory may spin off possibly

resulting in injury.

To engage the lock, depress the spindle lock button

and rotate the spindle until you are unable to rotate

the spindle further.

Mounting and Using Depressed

Center Grinding Wheels

MOUNTING AND REMOVING HUBBED WHEELS (FIG. 1, 7)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

remove battery pack before making

any adjustments or removing/installing

attachments or accessories.

Hubbed wheels install directly on the M14 threaded

spindle.

1. Thread the wheel on the spindle by hand.

2. Depress the spindle lock button and use a

wrench to tighten the hub of the wheel.

3. Reverse the above procedure to remove the

wheel.

CAUTION: Failure to properly seat

the wheel before turning the tool on

may result in damage to the tool or the

wheel.

MOUNTING NON-HUBBED WHEELS (FIG. 8)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

remove battery pack before making

any adjustments or removing/installing

attachments or accessories.

Depressed center Type 27 grinding wheels must be

used with included flanges.

1. Install the anti-lockup backing flange (g) on

spindle (d) with the raised centre against the

wheel. Be sure the backing flange recess is

seated onto the flats of the spindle by pushing

and twisting the flange before placing the

wheel.

2. Place wheel against the backing flange,

centering the wheel on the raised centre of the

backing flange.

3. While depressing the spindle lock button, thread

the clamp nut (h) on spindle. If the wheel you

are installing is more than 3.17 mm (1/8") thick,

place the threaded clamp nut on the spindle so

that the raised centre fits into the center of the

wheel (Fig. 8A). If the wheel you are installing is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt dc411n xj 18v 4 1 2 angle grinder bare Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info