Bedienungsanleitung DeWalt DC720K T 10 (Seite 15 von 20) (Englisch)

549321

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

torque and the larger the fastener which can be

driven. To select any of the numbers, rotate until the

desired number aligns with the arrow.

Dual Range Gearing (ﬁ g. 1)

The dual range feature of your driver/drill allows you

to shift gears for greater versatility.

To select the low speed, high torque setting, turn

the tool off and permit to stop. Slide the gear

selector (d) forward (towards the chuck) as shown

in Figure 1.

To select the high speed, low torque setting, turn the

tool off and permit to stop. Slide the gear selector

back (away from chuck).

NOTE: Do not change gears when the tool is

running. If you are having trouble changing gears,

make sure that the dual range gear selector is either

completely pushed forward or completely pushed

back.

Worklight (ﬁ g. 1)

There is a worklight (e) located just above the trigger

switch (a). The worklight will be activated when the

trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Keyless Single Sleeve Chuck (ﬁ g. 1)

Your tool features a keyless chuck (f) with one

rotating sleeve for one-handed operation of the

chuck. To insert a drill bit or other accessory, follow

these steps.

1. Lock the trigger in the OFF position as

previously described.

2. Grasp the black sleeve of the chuck with one

hand and use the other hand to secure the tool.

Rotate the sleeve counterclockwise far enough

to accept the desired accessory.

3. Insert the accessory about 19 mm into the

chuck and tighten securely by rotating the

chuck sleeve clockwise with one hand while

holding the tool with the other. Your tool is

equipped with an automatic spindle lock

mechanism. This allows you to open and close

the chuck with one hand.

To release the accessory, repeat step 2 above.

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to the

chuck and personal injury may result.

Always lock off trigger switch when

changing acces sories.

Be sure to tighten chuck with one hand on the

chuck sleeve and one hand holding the tool for

maximum tightness.

Drill Operation (ﬁ g. 4)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

disconnect tool from power source

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

1. Use sharp drill bits only. For WOOD, use the

low speed setting and twist drill bits, spade bits,

power auger bits, or hole saws. For METAL, use

the low speed setting and steel twist drill bits

or hole saws. For MASONRY, such as brick,

cement, cinder block, etc., use carbide-tipped

bits rated for percussion drilling. Use low speed

for bits greater than 10 mm.

2. Always apply pressure in a straight line with the

bit. Use enough pressure to keep drill biting, but

do not push hard enough to stall the motor or

deflect the bit.

3. Hold tool firmly with both hands to control

the twisting action of the drill. If model is not

equipped with side handle, grip drill with one

hand on the handle and one hand on the

battery pack.

CAUTION: Drill may stall if overloaded

causing a sudden twist. Always expect

the stall. Grip the drill firmly to control

the twisting action and avoid injury.

4. IF DRILL STALLS, it is usually because

it is being overloaded or improperly used.

RELEASE TRIGGER IMMEDIATELY, remove

drill bit from work, and determine cause of

stalling. DO NOT CLICK TRIGGER ON AND

OFF IN AN ATTEMPT TO START A STALLED

DRILL — THIS CAN DAMAGE THE DRILL.

5. To minimize stalling or breaking through the

material, reduce pressure on drill and ease the

bit through the last fractional part of the hole.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC720K T 10 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC720K T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info