Bedienungsanleitung DeWalt DC720K T 10 (Seite 16 von 20) (Englisch)

549321

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

7. With variable speed drills there is no need to

center punch the point to be drilled. Use a

slow speed to start the hole and accelerate by

squeezing the trigger harder when the hole is

deep enough to drill without the bit skipping

out.

Hammerdrill Operation (ﬁ g. 5)

1. Turn the collar (c) to the hammerdrill symbol.

2. Select the high speed setting by sliding the

selector back (away from the chuck).

IMPORTANT: Use carbide-tipped or masonry

bits only.

3. Drill with just enough force on the hammer to

keep it from bouncing excessively or “rising” off

the bit. Too much force will cause slower drilling

speeds, overheating and lower drilling rate.

4. Drill straight, keeping the bit at a right angle to

the work. Do not exert side pressure on the bit

when drillling as this will cause clogging of the

bit flutes and a slower drilling speed.

5. When drilling deep holes, if the hammer speed

starts to drop off, pull the bit partially out of the

hole with tool stil running to help clear debris

from the hole.

NOTE: A smooth, even flow of dust from the hole

indicates proper drilling rate.

Screwdriver Operation (ﬁ g. 6)

1. Select the desired speed/torque range using the

dual range gear selector to match the speed

and torque of the planned operation.

2. Turn the torque adjustment collar to the desired

position. Lower numbers indicate lower torque

settings; higher numbers indicate higher torque

settings.

3. Insert the desired fastener accessory into the

chuck as you would any drill bit.

4. Make some practice runs in scrap or on unseen

areas to determine the proper position of the

clutch collar.

5. Always start with lower torque settings, then

advance to higher torque settings to avoid

damage to the workpiece or fastener.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

tool from power source before

installing and removing accessories,

before making any adjustments or

removing/installing attachments or

accessories.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC720K T 10 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt DC720K T 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info