Bedienungsanleitung DeWalt DC900KL T 1 (Seite 29 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

549644

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

1 Variable speed switch

2 Forward/reverse slider

3 Keyless chuck/auto spindle lock

4 Torque adjustment collar

5 Mode selector

6 Three-gear selector

7 Bit holder

8 Grip

9 Side handle

10 Battery pack

Charger

Your DE9000 charger charger accepts D

E WALT

Li-Ion battery packs of 36 V at 2.2 Ah (DE9360).

10 Battery pack

11 Release button

12 Charger

13 Charging indicators (red)

Auto-spindle lock

The auto-spindle lock is engaged when the

transmission is stationary. The chuck sleeve can

easily be turned with one hand while the other

supports the unit.

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your D E WALT charger is double

insulated in accordance with EN 60335.

Mains plug replacement

(U.K. & Ireland only)

● Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

E WALT repair agent or a qualiﬁ ed electrician.

● Disconnect the plug from the supply.

● Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

● Only ﬁ t 13 Amperes BS1363A approved plugs

ﬁ tted with the correctly rated fuse (1).

● The cable wire colours, or a letter, will be

marked at the connection points of most good

quality plugs. Attach the wires to their

respective points in the plug (see below). Brown

is for Live (L) (2) and Blue is for Neutral (N) (4).

● Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable ﬁ rmly and that the two

leads are correctly ﬁ xed at the terminal screws.

Never use a light socket. Never connect

the live (L) or neutral (N) wires to the

earth pin marked E or .

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size

is 1 mm

; the maximum length is 30 m.

Assembly and adjustment

● Prior to assembly and adjustment,

always remove the battery pack.

● Always switch off the tool before

inserting or removing the battery pack.

Use only D E WALT battery packs and

chargers.

Fitting and removing the battery pack (ﬁ g. A)

● To ﬁ t the battery pack (10), line it up with the

receptacle on the tool. Slide the battery pack

into the receptacle and push until the battery

snaps into place.

● To remove the battery pack, push the release

button (11) while at the same time pulling the

battery pack out of the receptacle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DC900KL T 1 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info